Canon WUX10 manual Input selection parametersID, Component, Input is set to Video

Page 47

Projector WUX10 MarkII User Commands

INPUT

Input selection

Format

INPUT=<Input selection parameters:ID>

GETINPUT / ?INPUT

<Input selection parameters:ID>

D-RGB

D-RGB

A-RGB1

A-RGB1

A-RGB2

A-RGB2

COMP

Component

VIDEO

Video

HDMI

HDMI

Environment

 

Power

 

 

 

 

Input

OFF

ON

PM

D-RGB

A-RGB1

A-RGB2

COMP

VIDEO

HDMI

None

X

O

X

-

 

 

 

Response

"i:OK" is returned if the parameter was set properly.

For 'GET INPUT' or '?INPUT', current input selection is returned as

'g:INPUT=<Input selection parameters:ID>'

For details on other responses, refer to the "Error List".

Description

(1)This controls the input selection.

(2)This command is identical to pressing the “INPUT” button on the remote control.

(3)The input can be selected automatically using the auto setup command (AUTOSETEXE=INPUT).

(4)The current input can be acquired using the applicable GET command. ("GET INPUT")

Example

Setting

>

INPUT=VIDEO

The input is set to VIDEO.

<

i:OK

 

Reference

>GET INPUT or ?INPUT This retrieves the input signal.

< g:INPUT=A-RGB1

*Commands are indicated by ">", and responses are indicated by "<".

Revision History / Date

Changes

Revised by

Approved by

- 43 -

Image 47
Contents Projector WUX10 MarkII User Commands Revision History Table of Contents Error List Error Processing Other Appendix 1. Reset Items Same as or OverviewProjector can be controlled via serial or LAN connection Communication SpecificationsCommunication System Serial Request transmissions sent from PC to the projector Example Delimiters Delimiters for commands sent from PCERR response An error message is output ExampleCharacter string Or more Ascii characters 20h to 7Fh Or more Ascii characters 20h to 7FhTransmission sent Communication FlowAutopc Command SystemPower Auto SET Autosetexe Aspect Input Auto PC Autopc Command List PMM This includes the command function, conditions, and notes Details of CommandThis indicates the command format This describes the command responseControl For details on other responses, refer to the Error List6AXADJ R hue is set to -8, and the color saturation is set to Setting6AXR-Y IOK is returned if the parameter was set properlyDo not combine Auto focusing is executed during auto setup executionAscombo Auto set combination parameterID CombineAspect GASPECT=TRUE Setting This sets the screen size to WideASPECT=169 Autopc iOK AutopcAutosetexe Auto focusing is executedAvol SettingThis sets the volume to This retrieves the volumeReference BlankBlank parameterID Blank is set to onBlack screen Screen when Blank setting parameterIDSet to Black screen when screen is Blank BlankcolorReference This retrieves the brightness Setting values for Brightness settingNumber are -20 toSetting This sets the brightness to BRIThis mutes the Beep sound Beep sound settingNumber Beep sound mute Beep sound outputBVOL=Beep sound settingNumber BvolComver Returns the user command version asGCOMVER=User command versionCharacter string Reference This retrieves the contrast Setting values for Contrast settingNumber are -20 toSetting This sets the contrast to +3 ContThis sets the dynamic gamma function to Weak DgammaGDOTS=1200 DotsDOTS=Number of dotsNumber DOTS=1650Dpon This sets direct power-on to OFFDirect power-on is set to on ERR Fcontdrv Freezes image FreezeFreeze parameterID Image now frozen Image now not frozenFSTEPDRV=Focus lens step control parameterID FstepdrvFocus lens step control parameterID Ftoneadj This sets the gamma correction to Setting values for Gamma adjustment Number are -10 toGAMMA=Gamma adjustmentNumber GammaGuide display is set to on Guide setting parameter ID Guide display onGuide Guide display OFFGVPIX= HPIX/VPIXHPIX=1024 Reference This acquires the vertical position HPOS/VPOSReference This retrieves the hue Setting values for Hue setting valueNumber are -20 toSetting This sets the hue to +8 HUEImage GIMAGE=CINEMA Imageflip Video InputInput selection parametersID ComponentReference This retrieves the key lock state Setting This locks the remote control keysKeylock Silent cooling Lamp output setting parametersIDLamp NormalGLAMPCOUNTER=Lamp on timeCharacter string For all other responses, refer to Error ListLampcounter Returns current lamp on time asLang This sets the LED display to OFF Setting LED display is set to onLedilluminate Hours 34 minutes LmptNone Reference This retrieves the lamp time Main GMODE=REMOTE GMODE=LOCAL Mode switchMode reference ModeMute This returns the audio/beep sound to its original settingThis mutes the volume Reference GET Mute or ?MUTE This retrieves the volume stateGNOSIG=BLUE Parameters for setting display screen in no-signal modeIDThis sets the Blue screen when no signals are input NosigNo display Parameters for setting display screen at startupIDPjon Canon logoPMM Power management setting parametersIDExit mode Reference This retrieves the power management modePOWERParameterID PowerParameterID Power on Power OFFGPRODCODE=Product nameCharacter string ProdcodeProduct name is returned as Prog Progressive conversion setting parametersIDThis sets the progressive conversion setting to OFF DOWN+REP, Button press start Remote control emulation button parametersIDPOWEROFF, Power button pressed twice UP+REP, Button press startRC Power iOK Rcch Remote control setting parametersID Remote control channelThis sets the remote control channel to ch1 Current image adjustment reset ResetReset parametersID Lamp on time resetReset Lamptime Control This resets the lamp on timeRGB gain values are obtained Setting values for R/G/B gain settingNumber are -60 toSetting R gain is set to 10, G gain to 11 and B gain to RgbgainOr ?RGBOFFSET Setting values for R/G/B offset settingNumber are -60 toRgboffset RGB offset values are obtainedGROMVER=ROM versionCharacter string RomverROM version of the firmware is returned as GET SAT or ?SAT SATReference This retrieves the color saturation SAT=-10Reference This retrieves the screen aspect Setting This sets the screen aspect toScrnaspect 1610 DisplaySEL Input signal selection parameterID AUTOAutoSEL=Input signal selection parameterID GSEL=Detected input signalIDGSEL=575p Setting This sets the input signal selection to AutoReference This retrieves the input signal GET SEL or ?SELReference GET Sharp or ?SHARP This retrieves the sharpness Setting values for Sharpness settingNumber are -10 toSHARP=Sharpness settingNumber SharpGSIGNALSTATUS=Signal statusID SignalstatusCurrent image signal input status is returned as Signal statusIDGTEMP=5,37.1,63.0,38.9,29.7,32.4 TempNumber To 127.9 CGTMPL=5,71.0,90.0,57.0,44.0,53.0 Setting None ReferenceTmpl GTRACK=21 Tracking adjustment value is set toTRACK=Adjustment valueNumber TrackReference This retrieves the vertical keystone Setting This sets the vertical keystone toVKS Reference This retrieves the screen color correction AdjustSetting This sets the screen color correction to Normal Screen color correction parametersIDWbrgb Setting values for R/G/B adjustment valueNumber are -20 toSetting This sets R to 10, G to 11, and B to This retrieves the RGB adjustment valuesThis zooms to the wide-angle end ZcontdrvZoom lens continuous control parameterID This stops the zoomingZSTEPDRV=Zoom lens step control parameterID ZstepdrvZoom lens step control parameterID Badsequence Error ListSystem Unknown Start Error ProcessingYES Other Normal Lamp Appendix 1. Reset ItemsOFF PMM
Related manuals
Manual 2 pages 51.19 Kb

WUX10 specifications

The Canon WUX10 is a highly regarded projector that stands out in the realm of professional display technology. Renowned for its exceptional image quality and advanced features, it is an ideal choice for corporate environments, educational institutions, and event venues.

One of the most notable characteristics of the WUX10 is its WUXGA resolution (1920 x 1200 pixels), which supports 16:10 aspect ratios. This high definition capability ensures that media presentations are sharp, detailed, and vibrant, crucial for capturing the audience's attention and conveying information effectively. The projector utilizes Canon's proprietary AISYS technology, which enhances both brightness and contrast levels, allowing for dynamic visuals even in well-lit rooms.

With a brightness rating of up to 10,000 lumens, the WUX10 delivers clear projections even on large screens or in expansive spaces. This high lumen output is complemented by a contrast ratio of 2000:1, which means deeper blacks and more vivid colors, thereby enriching the viewing experience. The projector's ability to render images accurately makes it suitable for various applications, from corporate presentations to cinema-like experiences.

The Canon WUX10 also supports multiple connectivity options, including HDMI, VGA, and USB ports, as well as wireless capabilities, ensuring compatibility with an array of devices such as laptops, tablets, and smartphones. This versatility allows users to seamlessly stream content without the hassle of tangled cables.

In terms of maintenance and usability, the projector features a long lamp life of approximately 3,000 hours in normal mode and extended to 5,000 hours in eco mode. This longevity reduces the need for frequent replacements and minimizes downtime. Furthermore, a filter-free design simplifies cleaning and upkeep, making the WUX10 a practical solution for users.

With its compact and lightweight design, the Canon WUX10 is easy to transport and install, making it a favorite among professionals who require mobility without compromising on performance. This projector not only meets the demands of high-quality projection but also embodies Canon's commitment to innovation and user-friendliness.

In summary, the Canon WUX10 stands out for its impressive resolution, high brightness, robust connectivity options, and user-centric design. It is a solid investment for anyone looking to elevate their visual presentations.