Canon WUX10 manual Communication Specifications

Page 6

Projector WUX10 MarkII User Commands

2. Communication Specifications

Communication Specifications

The projector can be controlled via serial or LAN connection.

PC - Projector connection status

COM	SERVICE	LAN	LAN
PORT	PORT	PORT	PORT
		Canon	Network
			Connection
Dedicated cable		Projector	PC
PC		Projector	PC

	Item		Specifications
	Connection		PC and projector connected on
	system		a "1:1" basis

	Connection		3-line connection of SD,
	signal line		RD, and SG

	Connection		9pin RS-232C Cable (Cross)
	cable		9pin RS-232C Cable (Cross)
	cable

	Item		Specifications
	Connection		TCP/IP Connection
	system		TCP/IP Connection
	system

	Connection		Straight when connecting via
	signal line		network

	Connection		LAN Cable
	cable		LAN Cable
	cable

Send Data

Receive

Data

Signal

Ground

Send Data

Receive

Data

Signal

Ground

*Signal lines other than the three lines of SD, RD and SG are not used in the projector!

*Loop back its own signals at the PC side if necessary.

Revision History / Date

Changes

Revised by

Approved by

- 2 -

Image 6

Contents Projector WUX10 MarkII User Commands Revision History Table of Contents Error List Error Processing Other Appendix 1. Reset Items Overview Same as orCommunication Specifications Projector can be controlled via serial or LAN connectionCommunication System Serial Request transmissions sent from PC to the projector Example Delimiters Delimiters for commands sent from PCERR response An error message is output ExampleOr more Ascii characters 20h to 7Fh Character string Or more Ascii characters 20h to 7FhCommunication Flow Transmission sentCommand System AutopcPower Auto SET Autosetexe Aspect Input Auto PC Autopc Command List PMM This describes the command response Details of CommandThis indicates the command format This includes the command function, conditions, and notesFor details on other responses, refer to the Error List 6AXADJControl IOK is returned if the parameter was set properly Setting6AXR-Y R hue is set to -8, and the color saturation is set toAuto set combination parameterID Combine Auto focusing is executed during auto setup executionAscombo Do not combineAspect Setting This sets the screen size to Wide ASPECT=169GASPECT=TRUE Autopc Autopc iOKAuto focusing is executed AutosetexeThis retrieves the volume SettingThis sets the volume to AvolBlank is set to on BlankBlank parameterID ReferenceBlankcolor Screen when Blank setting parameterIDSet to Black screen when screen is Blank Black screenBRI Setting values for Brightness settingNumber are -20 toSetting This sets the brightness to Reference This retrieves the brightnessBvol Beep sound settingNumber Beep sound mute Beep sound outputBVOL=Beep sound settingNumber This mutes the Beep soundReturns the user command version as GCOMVER=User command versionCharacter stringComver Cont Setting values for Contrast settingNumber are -20 toSetting This sets the contrast to +3 Reference This retrieves the contrastDgamma This sets the dynamic gamma function to WeakDOTS=1650 DotsDOTS=Number of dotsNumber GDOTS=1200This sets direct power-on to OFF Direct power-on is set to onDpon ERR Fcontdrv Image now not frozen FreezeFreeze parameterID Image now frozen Freezes imageFstepdrv Focus lens step control parameterIDFSTEPDRV=Focus lens step control parameterID Ftoneadj Gamma Setting values for Gamma adjustment Number are -10 toGAMMA=Gamma adjustmentNumber This sets the gamma correction toGuide display OFF Guide setting parameter ID Guide display onGuide Guide display is set to onHPIX/VPIX HPIX=1024GVPIX= HPOS/VPOS Reference This acquires the vertical positionHUE Setting values for Hue setting valueNumber are -20 toSetting This sets the hue to +8 Reference This retrieves the hueImage GIMAGE=CINEMA Imageflip Component InputInput selection parametersID VideoSetting This locks the remote control keys KeylockReference This retrieves the key lock state Normal Lamp output setting parametersIDLamp Silent coolingReturns current lamp on time as For all other responses, refer to Error ListLampcounter GLAMPCOUNTER=Lamp on timeCharacter stringLang Setting LED display is set to on LedilluminateThis sets the LED display to OFF Lmpt None Reference This retrieves the lamp timeHours 34 minutes Main Mode Mode switchMode reference GMODE=REMOTE GMODE=LOCALReference GET Mute or ?MUTE This retrieves the volume state This returns the audio/beep sound to its original settingThis mutes the volume MuteNosig Parameters for setting display screen in no-signal modeIDThis sets the Blue screen when no signals are input GNOSIG=BLUECanon logo Parameters for setting display screen at startupIDPjon No displayReference This retrieves the power management mode Power management setting parametersIDExit mode PMMPower OFF PowerParameterID Power on POWERParameterIDProdcode Product name is returned asGPRODCODE=Product nameCharacter string Progressive conversion setting parametersID This sets the progressive conversion setting to OFFProg UP+REP, Button press start Remote control emulation button parametersIDPOWEROFF, Power button pressed twice DOWN+REP, Button press startRC Power iOK Remote control setting parametersID Remote control channel This sets the remote control channel to ch1Rcch Lamp on time reset ResetReset parametersID Current image adjustment resetControl This resets the lamp on time Reset LamptimeRgbgain Setting values for R/G/B gain settingNumber are -60 toSetting R gain is set to 10, G gain to 11 and B gain to RGB gain values are obtainedRGB offset values are obtained Setting values for R/G/B offset settingNumber are -60 toRgboffset Or ?RGBOFFSETRomver ROM version of the firmware is returned asGROMVER=ROM versionCharacter string SAT=-10 SATReference This retrieves the color saturation GET SAT or ?SAT1610 Display Setting This sets the screen aspect toScrnaspect Reference This retrieves the screen aspectGSEL=Detected input signalID Input signal selection parameterID AUTOAutoSEL=Input signal selection parameterID SELGET SEL or ?SEL Setting This sets the input signal selection to AutoReference This retrieves the input signal GSEL=575pSharp Setting values for Sharpness settingNumber are -10 toSHARP=Sharpness settingNumber Reference GET Sharp or ?SHARP This retrieves the sharpnessSignal statusID SignalstatusCurrent image signal input status is returned as GSIGNALSTATUS=Signal statusIDTo 127.9 C TempNumber GTEMP=5,37.1,63.0,38.9,29.7,32.4Setting None Reference TmplGTMPL=5,71.0,90.0,57.0,44.0,53.0 Track Tracking adjustment value is set toTRACK=Adjustment valueNumber GTRACK=21Setting This sets the vertical keystone to VKSReference This retrieves the vertical keystone Screen color correction parametersID AdjustSetting This sets the screen color correction to Normal Reference This retrieves the screen color correctionThis retrieves the RGB adjustment values Setting values for R/G/B adjustment valueNumber are -20 toSetting This sets R to 10, G to 11, and B to WbrgbThis stops the zooming ZcontdrvZoom lens continuous control parameterID This zooms to the wide-angle endZstepdrv Zoom lens step control parameterIDZSTEPDRV=Zoom lens step control parameterID Error List BadsequenceSystem Unknown Error Processing StartYES Other Appendix 1. Reset Items Normal LampOFF PMM

Related manuals

Manual 2 pages 51.19 Kb

WUX10 specifications

The Canon WUX10 is a highly regarded projector that stands out in the realm of professional display technology. Renowned for its exceptional image quality and advanced features, it is an ideal choice for corporate environments, educational institutions, and event venues.

One of the most notable characteristics of the WUX10 is its WUXGA resolution (1920 x 1200 pixels), which supports 16:10 aspect ratios. This high definition capability ensures that media presentations are sharp, detailed, and vibrant, crucial for capturing the audience's attention and conveying information effectively. The projector utilizes Canon's proprietary AISYS technology, which enhances both brightness and contrast levels, allowing for dynamic visuals even in well-lit rooms.

With a brightness rating of up to 10,000 lumens, the WUX10 delivers clear projections even on large screens or in expansive spaces. This high lumen output is complemented by a contrast ratio of 2000:1, which means deeper blacks and more vivid colors, thereby enriching the viewing experience. The projector's ability to render images accurately makes it suitable for various applications, from corporate presentations to cinema-like experiences.

The Canon WUX10 also supports multiple connectivity options, including HDMI, VGA, and USB ports, as well as wireless capabilities, ensuring compatibility with an array of devices such as laptops, tablets, and smartphones. This versatility allows users to seamlessly stream content without the hassle of tangled cables.

In terms of maintenance and usability, the projector features a long lamp life of approximately 3,000 hours in normal mode and extended to 5,000 hours in eco mode. This longevity reduces the need for frequent replacements and minimizes downtime. Furthermore, a filter-free design simplifies cleaning and upkeep, making the WUX10 a practical solution for users.

With its compact and lightweight design, the Canon WUX10 is easy to transport and install, making it a favorite among professionals who require mobility without compromising on performance. This projector not only meets the demands of high-quality projection but also embodies Canon's commitment to innovation and user-friendliness.

In summary, the Canon WUX10 stands out for its impressive resolution, high brightness, robust connectivity options, and user-centric design. It is a solid investment for anyone looking to elevate their visual presentations.