Canon WUX10 manual Fstepdrv, Focus lens step control parameterID

Page 37

Projector WUX10 MarkII User Commands

FSTEPDRV

Focus lens step drive control

Format

FSTEPDRV=<Focus lens step control parameter:ID>

<Focus lens step control parameter:ID>

FAR

This initiates focusing toward the far end.

NEAR

This initiates focusing toward the near end.

Environment

 

Power

 

 

 

 

Input

OFF

ON

PM

D-RGB

A-RGB1

A-RGB2

COMP

VIDEO

HDMI

None

X

O

X

-

 

 

 

Response

"i:OK" is returned when focusing was completed successfully after step drive. For details on other responses, refer to the "Error List".

Description

(1)This command is used to drive the focus lens.

(2)This command functions in the same way as when first the "FOCUS" button on the remote control or main unit panel is pressed and then the "←" or "→" button is pressed.

(3)The amount by which the lens is focused is constant, and it is fixed for the system.

(4)If a focusing error occurs, step drive cannot be controlled.

(5)There are no GET commands available for this command.

Example

Control

1-step control is exercised over the focus toward the NEAR end.

> FSTEPDRV=NEAR

<I:OK

*Commands are indicated by ">", and responses are indicated by "<"..

Revision History / Date

Changes

Revised by

Approved by

- 33 -

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Projector WUX10 MarkII User Commands Revision History Table of Contents Error List Error Processing Other Appendix 1. Reset Items Same as or OverviewProjector can be controlled via serial or LAN connection Communication SpecificationsCommunication System Serial Request transmissions sent from PC to the projector ERR response An error message is output Delimiters Delimiters for commands sent from PCExample ExampleCharacter string Or more Ascii characters 20h to 7Fh Or more Ascii characters 20h to 7FhTransmission sent Communication FlowAutopc Command SystemPower Auto SET Autosetexe Aspect Input Auto PC Autopc Command List PMM This indicates the command format Details of CommandThis describes the command response This includes the command function, conditions, and notes6AXADJ For details on other responses, refer to the Error ListControl 6AXR-Y SettingIOK is returned if the parameter was set properly R hue is set to -8, and the color saturation is set toAscombo Auto focusing is executed during auto setup executionAuto set combination parameterID Combine Do not combineAspect ASPECT=169 Setting This sets the screen size to WideGASPECT=TRUE Autopc iOK AutopcAutosetexe Auto focusing is executedThis sets the volume to SettingThis retrieves the volume AvolBlank parameterID BlankBlank is set to on ReferenceSet to Black screen when screen is Blank Screen when Blank setting parameterIDBlankcolor Black screenSetting This sets the brightness to Setting values for Brightness settingNumber are -20 toBRI Reference This retrieves the brightnessBVOL=Beep sound settingNumber Beep sound settingNumber Beep sound mute Beep sound outputBvol This mutes the Beep soundGCOMVER=User command versionCharacter string Returns the user command version asComver Setting This sets the contrast to +3 Setting values for Contrast settingNumber are -20 toCont Reference This retrieves the contrastThis sets the dynamic gamma function to Weak DgammaDOTS=Number of dotsNumber DotsDOTS=1650 GDOTS=1200Direct power-on is set to on This sets direct power-on to OFFDpon ERR Fcontdrv Freeze parameterID Image now frozen FreezeImage now not frozen Freezes imageFocus lens step control parameterID FstepdrvFSTEPDRV=Focus lens step control parameterID Ftoneadj GAMMA=Gamma adjustmentNumber Setting values for Gamma adjustment Number are -10 toGamma This sets the gamma correction toGuide Guide setting parameter ID Guide display onGuide display OFF Guide display is set to onHPIX=1024 HPIX/VPIXGVPIX= Reference This acquires the vertical position HPOS/VPOSSetting This sets the hue to +8 Setting values for Hue setting valueNumber are -20 toHUE Reference This retrieves the hueImage GIMAGE=CINEMA Imageflip Input selection parametersID InputComponent VideoKeylock Setting This locks the remote control keysReference This retrieves the key lock state Lamp Lamp output setting parametersIDNormal Silent coolingLampcounter For all other responses, refer to Error ListReturns current lamp on time as GLAMPCOUNTER=Lamp on timeCharacter stringLang Ledilluminate Setting LED display is set to onThis sets the LED display to OFF None Reference This retrieves the lamp time LmptHours 34 minutes Main Mode reference Mode switchMode GMODE=REMOTE GMODE=LOCALThis mutes the volume This returns the audio/beep sound to its original settingReference GET Mute or ?MUTE This retrieves the volume state MuteThis sets the Blue screen when no signals are input Parameters for setting display screen in no-signal modeIDNosig GNOSIG=BLUEPjon Parameters for setting display screen at startupIDCanon logo No displayExit mode Power management setting parametersIDReference This retrieves the power management mode PMMParameterID Power on PowerPower OFF POWERParameterIDProduct name is returned as ProdcodeGPRODCODE=Product nameCharacter string This sets the progressive conversion setting to OFF Progressive conversion setting parametersIDProg POWEROFF, Power button pressed twice Remote control emulation button parametersIDUP+REP, Button press start DOWN+REP, Button press startRC Power iOK This sets the remote control channel to ch1 Remote control setting parametersID Remote control channelRcch Reset parametersID ResetLamp on time reset Current image adjustment resetReset Lamptime Control This resets the lamp on timeSetting R gain is set to 10, G gain to 11 and B gain to Setting values for R/G/B gain settingNumber are -60 toRgbgain RGB gain values are obtainedRgboffset Setting values for R/G/B offset settingNumber are -60 toRGB offset values are obtained Or ?RGBOFFSETROM version of the firmware is returned as RomverGROMVER=ROM versionCharacter string Reference This retrieves the color saturation SATSAT=-10 GET SAT or ?SATScrnaspect Setting This sets the screen aspect to1610 Display Reference This retrieves the screen aspectSEL=Input signal selection parameterID Input signal selection parameterID AUTOAutoGSEL=Detected input signalID SELReference This retrieves the input signal Setting This sets the input signal selection to AutoGET SEL or ?SEL GSEL=575pSHARP=Sharpness settingNumber Setting values for Sharpness settingNumber are -10 toSharp Reference GET Sharp or ?SHARP This retrieves the sharpnessCurrent image signal input status is returned as SignalstatusSignal statusID GSIGNALSTATUS=Signal statusIDNumber TempTo 127.9 C GTEMP=5,37.1,63.0,38.9,29.7,32.4Tmpl Setting None ReferenceGTMPL=5,71.0,90.0,57.0,44.0,53.0 TRACK=Adjustment valueNumber Tracking adjustment value is set toTrack GTRACK=21VKS Setting This sets the vertical keystone toReference This retrieves the vertical keystone Setting This sets the screen color correction to Normal AdjustScreen color correction parametersID Reference This retrieves the screen color correctionSetting This sets R to 10, G to 11, and B to Setting values for R/G/B adjustment valueNumber are -20 toThis retrieves the RGB adjustment values WbrgbZoom lens continuous control parameterID ZcontdrvThis stops the zooming This zooms to the wide-angle endZoom lens step control parameterID ZstepdrvZSTEPDRV=Zoom lens step control parameterID Badsequence Error ListSystem Unknown Start Error ProcessingYES Other Normal Lamp Appendix 1. Reset ItemsOFF PMM
Related manuals
Manual 2 pages 51.19 Kb

WUX10 specifications

The Canon WUX10 is a highly regarded projector that stands out in the realm of professional display technology. Renowned for its exceptional image quality and advanced features, it is an ideal choice for corporate environments, educational institutions, and event venues.

One of the most notable characteristics of the WUX10 is its WUXGA resolution (1920 x 1200 pixels), which supports 16:10 aspect ratios. This high definition capability ensures that media presentations are sharp, detailed, and vibrant, crucial for capturing the audience's attention and conveying information effectively. The projector utilizes Canon's proprietary AISYS technology, which enhances both brightness and contrast levels, allowing for dynamic visuals even in well-lit rooms.

With a brightness rating of up to 10,000 lumens, the WUX10 delivers clear projections even on large screens or in expansive spaces. This high lumen output is complemented by a contrast ratio of 2000:1, which means deeper blacks and more vivid colors, thereby enriching the viewing experience. The projector's ability to render images accurately makes it suitable for various applications, from corporate presentations to cinema-like experiences.

The Canon WUX10 also supports multiple connectivity options, including HDMI, VGA, and USB ports, as well as wireless capabilities, ensuring compatibility with an array of devices such as laptops, tablets, and smartphones. This versatility allows users to seamlessly stream content without the hassle of tangled cables.

In terms of maintenance and usability, the projector features a long lamp life of approximately 3,000 hours in normal mode and extended to 5,000 hours in eco mode. This longevity reduces the need for frequent replacements and minimizes downtime. Furthermore, a filter-free design simplifies cleaning and upkeep, making the WUX10 a practical solution for users.

With its compact and lightweight design, the Canon WUX10 is easy to transport and install, making it a favorite among professionals who require mobility without compromising on performance. This projector not only meets the demands of high-quality projection but also embodies Canon's commitment to innovation and user-friendliness.

In summary, the Canon WUX10 stands out for its impressive resolution, high brightness, robust connectivity options, and user-centric design. It is a solid investment for anyone looking to elevate their visual presentations.
Top Page Image Contents