Compaq SMA200 user manual Sata Interface Option, If the signals are not used

Page 35

DIGITAL-LOGIC AG

SMA200 Manual V1.0

5.4.11.SATA Interface (Option)

 

 

 

 

On Module

Ext. Ter-

Max.

 

Matched

Signal

BUS

Type

Description

Termination

mination

Length

Ohm

Length

 

 

 

 

 

Needed

in mm

 

in mm

SATA_Tx[0..3] SATA SATA_Rx[0..3] SATA

Dif Dif

SATA transmitter pair SATA receiver pair

Series 10nF Series 10nF

100

100

100

100

-

-

If the signals are not used:

Unused SATA interfaces may be open.

Remarks:

The 10nF capacitors 0402 need to be placed directly at the SATA connector.

Maximum via count is 2 per signal.

BUS to BUS spacing is min. 20mil = 0.5mm

Pair to Pair spacing is min. 35mil = 0.9mm

The SATA_LED# output show the SATA (all ports) activity. The LED must be connected to +3.3V with a series resistor of 330 Ohm to the “SATA_LED#” signal.

EMV/EMI filters:

Are not needed.

35

Image 35
Contents SmartCore Express SMA200 Initial Version About this Manual and How to Use ItSMA200 Manual Table of Contents Environmental Protection Statement PrefaceTrademarks DisclaimerTechnical Support Limited Two Year WarrantyRecycling Information CE Conformity Explanation of SymbolsApplicable Documents and Standards RoHS Commitment For Your SafetyWeee Application RoHS Compatible Product DesignRoHS Compliant Production Process Swiss Association for Quality and Management Systems Swiss QualityOverview Standard FeaturesMathematics Coprocessor Technical SpecificationsSpecification Intel US15W Graphics Memory Controller Hub SpecificationPhysical Characteristics Specification Intel US15W SpecificationReset & Power Management Specification Power Supply SpecificationExamples of Ordering Codes Operating Environment SpecificationEMI / EMC IEC1131-2 refer MIL 461/462 Specification Options/AccessoriesBlock Diagram Dimensions & DiagramsDesign in with the smartModule Dimensions of the smartCoreExpress ModuleConnector Placement & Pin Definition on the Carrier Board Photo of the Top Side of the PCB Component Heights between Module and Carrier Board Dimensions of the Carrier Board ConnectorSignal Description COM-EXPRESS Connector DescriptionSignal Terminology Descriptions Type Remarks SmartCoreExpress Connector PinoutBUS on the smartCoreExpress Connectors a / B Pins Signal Type Remarks Pin SignalType Signal BUS TypeSignal Descriptions of the Smartcoreexpress Placing an AC Coupling Capacitor on each PCIe-TX PCI-Express SmartCoreExpress Signal GroupsSupported devices SdvoLvdsclk + Lvdsvdden Lvdsbklctl Lvdsbklen Lvdsctlaclk LvdsLvdsddcclk Lvdsddcdat Remarks EMV/EMI-filters USBOn Module Ext. Ter Max Matched USBRemarks EMV/EMI filters Parallel ATALpcserirq LPC BUSLPCFRAME# Smbclock Cmos SMBusSMBALERT# Cmos Smbdata CmosSupported Codecs EMV/EMI filters If the signals are not used RemarksHDA Audio Interface SD / Sdio Interface If the signals are not used Remarks EMV/EMI filtersSpimiso Spimosi Spiclk SPICS# Cmos SPI BUSSata Interface Option Lcirst LCI GlanGlantx + Glanrx + GLAN-CLK + LCICanrx Cmos Can / SerialCantx Cmos 14. PM Vccrtc PWR PWR PWR SupplyTyco / AMP SMARTCORE-EXPRESS Connector SpecificationsParameter Condition Specification Source on smartCore Part Name Part NumberSMARTCORE-EXPRESS Versus Comexpress Index Coprocessor Design Dimensions