Christie Digital Systems LX66A user manual Background, Lamp

Page 51

Setting

PIN Code Change

Logo PIN code can be changed to your desired four-digit number. Select “PIN code change” with the Point buttons (e, d, 7, and 8) or the Control pad and press the SELECT button. Set a new Logo PIN code.

Be sure to note the new Logo PIN code and keep it at hand. If you lost the number, you could no longer change the Logo PIN code setting. For details on PIN code setting, refer to relevant instructions of the PJ Lock function on page 55.

Background

Three background settings are available in this projector. Select one of the followings when no input source is connected to the projector or no input signal is coming from the connected equipment:

Blue . . . . . .blue colored background My logo . . .the image you captured Black . . . . .black colored background

Lamp

Control

This feature allows you to change brightness of the screen.

Normal . .normal brightness

Auto . . . .brightness according with the input signal Eco . . . .lower brightness reduces the lamp power

consumption and extends the lamp life.

Mode

This projector is equipped with two lamps. Mode setting allows you to switch using one (1) lamp or two (2) lamps.

2-Lamp . . . .light both of the lamps inside the projector.

1-Lamp . . . .light one lamp only. Auto, Lamp 1, or Lamp 2 can be altered.

Note:

When neither of the two lamps is lighted, the projector will shutdown automatically.

When either of the two lamps does not light up, the LAMP 1/2 REPLACE indicator blinks orange and the projector will light the other automatically.

After changing the lamp mode, it cannot be switched again for 90 seconds.

Remote control

Four (4) remote control channels and eight (8) remote control ID are prepared for the projector to prevent radio frequency interference from the other equipment and mutual interference between projectors when using them at the same time.

For example, operating the projector in “CH-2 and ID-7,” both the projector and the remote control must be switched to “CH-2 and ID-7.”

To change CH and ID for the projector;

Select a Remote control CH and ID in this Setting menu.

To change CH and ID for the remote control;

While holding down the CH or ID button and press the SELECT button. The Remote control CH or ID switches sequentially for one pressing the SELECT button. Changing CH and ID should be done separately. (See page 16 and 17 for details.)

PIN Code change Dialog Box

Select PIN code change and press the SELECT button. The PIN code input dialog box will appear.

Pointer

Lamp Control

Lamp Mode

When selecting Auto in 1-Lamp mode, the projector automatically selects either lamp of which the total Lamp time is shorter and lights it up.

Remote control

Pointer

The setting selected.

When pressing the SELECT button at Remote control, the remote control CH and ID menu appears. Select CH and ID respectively.

Setting

51

Image 51
Contents LX66A Compatibility My Menu Selection Features and DesignTable of Contents Risk of Electric Shock Do not Open To The OwnerVoor de klanten in Nederland Safety InstructionsBottom Front Downward Upward Usual Setup In Proper DirectionsPositioning Precautions Air CirculationUSE Caution in Carrying or Transporting the Projector Moving the ProjectorFederal Communication Commission Notice ComplianceBack PreparationParts Name FrontIndicators Top Control Input 2 terminals TerminalsSerial Port OUT USB Series BC Jack USBAbout Control Pad Remote ControlCH button Timer button4REMOTE RESET/ON/ALL-OFF switch Freeze buttonRemote Control Transmitter Remote Control Channel and ID SetupWired Remote Control Transmitter Remote Control Battery Installation Remote Control Channel & FrequencyRemote Control ID Positioning the Projector InstallationInstallation Lens InstallationLens Shift Adjustment Level Adjustable FeetAdjustable feet 200 240 V AC Connecting AC Power CordFor Continental Europe For the U.S.A. and CanadaConnection Terminals Interface Board SlotsOption Control No Cables used for connection Connecting to Computer Digital and Analog RGBConnecting to Video Equipment Digital and Video Connecting to Video Equipment Component and RGB Scart Mouse Operation Wireless Remote Control OperationBasic Operation Operating the ProjectorTop Control Remote Control Basic Operation and Reference ButtonsPad What is PIN code? Turning On the ProjectorEnter a PJ PIN code Turning Off the Projector Top Control Zoom and Focus AdjustmentRemote Control Shutter FunctionAuto PC Adjustment Input SelectionInformation Picture Freeze Function Keystone AdjustmentTimer Function Screen SelectionZoom +/- Function Zoom +Zoom Mouse Operation How to Operate On-Screen MenuRemote Control Operation Top Control OperationItem data Menu icon GuideControl bar for Mouse Operation Mouse cursorMenu icons What You Can Do with Each Menu Menu Icons and Their FeaturesInput InputRGB Scart Move a pointer to Input 2 and press the Select button When the input source is analog comingWhen video input signal is connected to When the input source is componentAuto SystemSystem PC System SelectionAV System Menu Component Video or S-Video Signal SelectionComponent Signal Selection AV System Menu Video or S-VideoAuto PC adj Computer AdjustmentPC Adjustment Auto PC AdjustManual PC Adjust Mode Sync phaseReset PositionFor AV Input Image AdjustmentImage For PC InputImage Adjust Green Auto picture controlColor temp RedFilm GammaNoise reduction ProgressiveScreen Setting Screen SettingScreen Rear ZoomKeystone CeilingMenu SettingSetting LanguageEnter a Logo PIN code LogoLamp BackgroundInput search Power managementPower management DisplayAnalog out Lens memoryShutter USB lock Shutter ManagementSecurity Key lockTo Change PJ PIN Code To Change the PJ PIN Code settingExits the Setting menu Factory defaultFilter SpecialSpecial Fan controlTest pattern RS-232CUSB memory Information Exits Warning log menuMaintenance and Cleaning All indicators except the Lamp indicator are blinkingThen check the matters below Filter cover Air filter Air Filter ReplacementLamp Replacement Reset the Lamp timeLamp Lamp Handling Precautions Cleaning the Projection Lens Cleaning the Projector CabinetAttaching the Cord Cover Strap May cause electric shock or a fire hazard Indicators and Projector ConditionMain Indicators Projector is OFF. The AC power cord is unpluggedAir filter is clogged with dust or has been used overtime Shutter IndicatorLamp Replace Indicators Lamp 1/2Until cooling is completed Appendix TroubleshootingSome displays are not seen Wireless Remote ControlLens position moves when Input Is switchedFreq Compatible Computer Specifications1080i/50 1080i/60Technical Specifications Optional Parts AccessoriesScreen Screen Menu TreeImage Image ADJ Special Lamp Dimensions USB Connector Series B Terminal ConfigurationsPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Numerics IndexAppendix Appendix Appendix Part No -A 610 328 2459 1AA6P1P5105-- KH6K