BOXLIGHT MP-93i Connection to the video signal terminals, Connection to the RGB signal terminal

Page 19

Connection to the video signal terminals

1. Input signal

S-VIDEO signal			Luminance signal	1.0Vp-p, 75Ω termination
S-VIDEO signal			Chrominance signal	0.286Vp-p (burst signal), 75Ω termination		ENGLISH
			Chrominance signal	0.286Vp-p (burst signal), 75Ω termination

VIDEO signal		Output		0~200mVrms, 1kΩ
VIDEO signal				1.0Vp-p, 75Ω termination
AUDIO signal		Input		200mVrms, 20kΩ below (MAX 3.0Vp-p)
AUDIO signal

2. Signal input terminal
2. Signal input terminal
		Chrominance signal		Luminance signal

	Ground	Ground
	Ground
	S VIDEO input (Mini DIN4 pin)
Caution	Video input signal terminals have priority in the following order.
Caution
	1 S-VIDEO input terminal 2 RCA jack input terminal

Even when the video signal is displayed, only an audio signal is output to RGB audio output terminals.

Connection to the RGB signal terminal

1. Input / output signal

	Video signal		Analog 0.7Vp-p 75Ω termination (Positive polarity)

	Horizontal sync signal		TTL level (Positive/negative polarity)

	Vertical sync signal		TTL level (Positive/negative polarity)

	Composite sync signal		TTL level

	Audio signal	Input	200mVrms, 20kΩ below (MAX 3.0Vp-p)

		Output	0~200mVrms, 1kΩ
		Output	0~200mVrms, 1kΩ

2. Signal input / output terminal

1	Video signal (Red)	9	N.C

2	Video signal (Green)	10	Ground

3	Video signal (Blue)	11	N.C

4	N.C	12	DDC (Display Data channel) RGB1 only

5	N.C	13	Horizontal/Composite sync signal

6	Ground (for R)	14	Vertical sync signal

7	Ground (for G)	15	DDC (Display Data channel) RGB1 only

8	Ground (for B)

5 1

106

15 11

D-sub 15pin shrink terminal (Female)

	Caution	Do not use RGB cable other than that specified.
	Caution	Some RGB cable may not operate DDC (Display Data Channel)
		Some RGB cable may not operate DDC (Display Data Channel)
		because there are not connect from pin NO. 15 to pin NO. 12 .

19

Image 19

Contents Operating Guide FeaturesContents OutlineFor the Customers in U.K Instructions to Users Video signal cablesPower cord Before useIf any abnormality occurs Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place Do not use power supplies other Than that specifiedDo not step on this unit or do not put a Heavy object on it Be careful in handling the power cordCleaning Handle the power cord carefullyVolume When you are not going to use For a long timeClean inside the unit at least once two years Do not place this unit where it gets hotNames and functions of each part Contents of shipping boxRGB input terminal Remote control sensor Main Power switchAC in socket Video input terminalRemote control transmitter Remove the battery compartment cover How to insert batteriesExample of the projector and screen installation InstallationHow to use foot adjusters To project the picture Basic operationsPLUG&PLAY To turn off the powerIndicator lights up orange Standby modeMagnifying Function Freeze FunctionOn-screen menus are displayed on the screen Adjustments and functionsTo return to the initial setting Memory functionManual Operation SET UPHow to use the SET UP menu Adjustment Item Details of adjustment Freeze MagnifyAdjustment Item Details of adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen During AUTO-adjustmentMenu OPT. allows you to control communication function etc ImageOPT Menu Image serves of the picture inversionConnection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Type Example of computer signalComputer/signal Horizontal Timing µs Initial set signalsComputer/signal Vertical Timing lines +5V Control signal terminalPin No RS-232C Mouse PS/2 SerialADB Mac mouse PS/2 mouseSerial mouse RS232C cable Reference Control command tableControl command table CommunicationControl data table Example of command error Procedure of getting the Projector statusProcedure of setting the Projector status Procedure of default setting the Projector statusComputerDesk type Example of system setupConnecting various equipment AC Inlet Computer Note typeAir filter Filter cover Cleaning the air filterDo not use with removed air filter Remove the lamp cover How to replace lampLoosen two screws and pull the handle to remove Lamp Message table Install the lamp cover and fix it using screwsReset the lamp time LampBlink in the following cases Indicator displayRCA Jack terminal Terminal Dimension diagramAll dimensions shown in inches RCA Jack terminal Input terminal Input/Output