BOXLIGHT MP-93i Remove the lamp cover, Loosen two screws and pull the handle to remove Lamp

Page 29

Lamp

Light source lamp has a service life.

The picture will become dark or color will be poor when the lamp is used for a long time.

If usage of lamp is continued in such cases, it could cause a malfunction. Replace lamp with new one.

As reference for replacement time, indicator will operate or message will be displayed when the power is turned on, as shown on page 30~31. In these cases the lamp should be replaced. Consult your dealer.

Caution

Also LAMP indicator will light when the lamp becomes too hot. Turn off the power and let the

projector cool for 45 minutes. Turn on. If LAMP indicator still lights up red, contact your

 

 

dealer.

1. How to replace lamp

(Option lamp : Lamp unit DT00201)

 

 

HIGH VOLTAGE

 

HIGH TEMPERATURE

 

HIGH PRESSURE

When replacing lamp, turn off and remove AC cord, wait 45 minutes to let lamp cool. High-pressure lamp when hot, may explode if improperly handled.

Caution • For disposal of used lamp, treat according to the instruction of community authorities.

•Since the lamp is made of glass, do not apply shock to it and do not scratch it.

•Also, do not use old lamp. This could also cause explosion of the lamp.

• If it is probable that the lamp has exploded

Reflector

Front glass

(explosive sound is heard), disconnect the power

 

 

 

plug from the power outlet and ask your dealer to

 

 

replace lamp. The lamp is covered by front glass

 

Lamp

and air-tight structure, but, in rare cases, the

 

 

 

 

 

reflector and the inside of the projector may be damaged by scattered broken pieces of glass,

 

 

and broken pieces could cause injury when being handled.

 

 

 

 

1

Turn the main power switch off and disconnect the power

 

 

plug from the power outlet.

 

 

 

2

Remove the lamp cover.

 

• If lamp is hot at this time, this could cause burn. Wait

for minimum 45 minutes until lamp is cooled down.

Lamp cover

Screw

• Loosen a screw and remove the cover.

 

 

 

ENGLISH

3 Loosen two screws and pull the handle to remove the

lamp.

Screw

• If the screws are not loosened completely, your fingers

may be damaged.

Lamp

•Do not insert your hand into the box after the lamp is removed.

(There are optical parts inside. If touched by hand, it may result in color unevenness, etc.)

4

Replace the lamp with new one and

 

fix it using the same two screws.

• Firmly tighten the lamp screws. Loose screws may cause bad connection of the connector which in turn may result in malfunctioning.

Screw

Lamp

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Contents FeaturesOutline Operating GuideFor the Customers in U.K Power cord Video signal cablesBefore use Instructions to UsersDo not install this unit in an unstable place Do not look directly at the lens when Lamp is litDo not use power supplies other Than that specified If any abnormality occursCleaning Be careful in handling the power cordHandle the power cord carefully Do not step on this unit or do not put a Heavy object on itClean inside the unit at least once two years When you are not going to use For a long timeDo not place this unit where it gets hot VolumeNames and functions of each part Contents of shipping boxAC in socket Remote control sensor Main Power switchVideo input terminal RGB input terminalRemote control transmitter Remove the battery compartment cover How to insert batteriesHow to use foot adjusters InstallationExample of the projector and screen installation To project the picture Basic operationsIndicator lights up orange To turn off the powerStandby mode PLUG&PLAYMagnifying Function Freeze FunctionTo return to the initial setting Adjustments and functionsMemory function On-screen menus are displayed on the screenHow to use the SET UP menu SET UPAdjustment Item Details of adjustment Freeze Magnify Manual OperationAUTO-adjustment Confirm Screen AUTO-adjustmentDuring AUTO-adjustment Adjustment Item Details of adjustmentOPT ImageMenu Image serves of the picture inversion Menu OPT. allows you to control communication function etcConnection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Type Example of computer signalComputer/signal Vertical Timing lines Initial set signalsComputer/signal Horizontal Timing µs Pin No RS-232C Mouse PS/2 Control signal terminalSerial +5VSerial mouse PS/2 mouseADB Mac mouse Control command table Control command tableCommunication RS232C cable ReferenceControl data table Procedure of setting the Projector status Procedure of getting the Projector statusProcedure of default setting the Projector status Example of command errorConnecting various equipment Example of system setupAC Inlet Computer Note type ComputerDesk typeDo not use with removed air filter Cleaning the air filterAir filter Filter cover Loosen two screws and pull the handle to remove Lamp How to replace lampRemove the lamp cover Reset the lamp time Install the lamp cover and fix it using screwsLamp Message tableBlink in the following cases Indicator displayAll dimensions shown in inches Dimension diagramRCA Jack terminal Input terminal Input/Output RCA Jack terminal Terminal
Top Page Image Contents