BOXLIGHT MP-93i specifications Control signal terminal, Pin No RS-232C Mouse PS/2, Serial, +5V

Page 22

Connection to the control signal terminal

1. Control signal terminal

	Pin No.	RS-232C		Mouse

			PS/2	ADB	Serial
			PS/2	ADB	Serial

	1

	2		CLK

	3		DATA	DATA

	4

	5

	6	SELO	SELO		SELO

	7	RTS	RTS	RTS	RTS

	8

	9		+5V	+5V

	10	GND	GND	GND	GND

	11

	12

	13	RDP

	14	TDP			TD

	15

1 5

610

11 15

D-sub 15pin shrink terminal (Male)

	Caution	Turn off the power of both the projector and computer before connecting.
	Caution	Connect the computer to the control terminal of the projector using an appropriate cable.

		Refer to the instruction manual of each device before connecting.

2.Mouse emulation

(1)Connect the projector and the mouse terminal of computer using an appropriate cable, while the projector and the computer are turn off.

(2)Turn the main power switch of the projector on and press the STANDBY/ON button. The indicator will light. (The ON indicator will light up green.).

(3)Press the INPUT of the projector or RGB button of the remote control transmitter and select the input connection.

(4)Turn on the computer.

(5)Start mouse emulation mode.

If can not start mouse emulation, reset the computer. (With soft reset or reset switch)

(6)See on the page 9 about to operate the remote control transmitter.

Caution : Mouse cannot be operated while start up screen or menu screen is being displayed.

	Caution	• In some note computers which have internal pointing device, mouse emulation don't work
	Caution	without setting the internal pointing device disabled. In this case, set the internal pointing

		device disabled in BIOS setting. After setting in BIOS, operate (1) ~ (5) Please check its
		hardware manuals to disable internal pointing device in BIOS setting.

•In some computers, mouse emulation don't work without the utility program. In this case, see and check the operating manuals of the computer.

22

Image 22

Contents Outline FeaturesContents Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursHandle the power cord carefully Be careful in handling the power cordCleaning Do not step on this unit or do not put a Heavy object on itDo not place this unit where it gets hot When you are not going to use For a long timeClean inside the unit at least once two years VolumeContents of shipping box Names and functions of each partVideo input terminal Remote control sensor Main Power switchAC in socket RGB input terminalRemote control transmitter How to insert batteries Remove the battery compartment coverExample of the projector and screen installation InstallationHow to use foot adjusters Basic operations To project the pictureStandby mode To turn off the powerIndicator lights up orange PLUG&PLAYFreeze Function Magnifying FunctionMemory function Adjustments and functionsTo return to the initial setting On-screen menus are displayed on the screenAdjustment Item Details of adjustment Freeze Magnify SET UPHow to use the SET UP menu Manual OperationDuring AUTO-adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen Adjustment Item Details of adjustmentMenu Image serves of the picture inversion ImageOPT Menu OPT. allows you to control communication function etcConnection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeComputer/signal Horizontal Timing µs Initial set signalsComputer/signal Vertical Timing lines Serial Control signal terminalPin No RS-232C Mouse PS/2 +5VADB Mac mouse PS/2 mouseSerial mouse Communication Control command tableControl command table RS232C cable ReferenceControl data table Procedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Computer Note type Example of system setupConnecting various equipment ComputerDesk typeAir filter Filter cover Cleaning the air filterDo not use with removed air filter Remove the lamp cover How to replace lampLoosen two screws and pull the handle to remove Lamp Lamp Install the lamp cover and fix it using screwsReset the lamp time Message tableIndicator display Blink in the following casesRCA Jack terminal Input terminal Input/Output Dimension diagramAll dimensions shown in inches RCA Jack terminal Terminal