BOXLIGHT FP-95t manual Important Safety Instructions

Page 3

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other material, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord will be abused by persons walking on it.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f.When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

 

This projector is equipped with a

 

 

grounding type AC line plug.

 

Should you be unable to insert the

 

plug into the outlet, contact your

 

electrician. Do not defeat the safety

GROUND

purpose of this grounding type plug.

 

 

 

Follow all warnings and instructions marked on the projectors.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and powerline surges.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained.

Do not cover the ventilation slot on the projector.

Heat build-up can reduce the service life of your projector, and can also be dangerous.

50cm

 

WALL

 

 

PROJECTOR

PROJECTOR

 

(FRONT)

(SIDE)

 

50cm

50cm

50cm

3

Image 3
Contents Boxlight To the Owner Important Safety Instructions Table of Contents Features and Design Rear of the Projector InstallationName of Each Part of the Projector Front of the ProjectorRoom Light SETTING-UP the ProjectorAdjustable Feet PositioningMoving the Projector VentilationExhaust Vent AIR Intake Ventrear Side Bottom Side Projector side Female AC outlet side Male Power RequirementsConnecting the Projector Terminal of the ProjectorSide of the Projector Connect the Computer Video Monitor S-VIDEO Output Jack Side of the Projector Connect the Video EquipmentVideo Input JACK-1 Video Input JACK-2Control Port Cable Removal Hint Connecting the ComputerHDB 15-PIN Terminal Connecting to the Monitor Output Terminal Analog HDB 15-PINConnecting to the Audio Monitor Output Variable Jacks Connecting to the Serial Port DB 9-PIN TerminalConnecting AN IBM-COMPATIBLE Desktop Computer Speaker L Connecting AN IBM-COMPATIBLE Laptop Computer PS/2 Port Provided Connecting a Macintosh Desktop Computer Connecting a Macintosh Powerbook Computer Connecting the Video Equipment Connecting to the S-VHS Video Monitor Output JackConnecting to the Audio Monitor Output Jacks Video Equipment Connecting the Video EquipmentBefore Operation Controls and IndicatorsFront Indicators TOP Controls Front Indicators TOP ControlsLamp Power Indicator Lamp Replacement IndicatorTemperature Warning Indicator Ready IndicatorOperation of the Remote Control Wireless Remote Control UnitLaser Light Window Zoom Button Timer ButtonComputer Select Button Video Select ButtonRemote Control Battery Installation 1714 Wired Remote Cable Using the Remote Control Unit wirelessDirect Operation Control the ProjectorCOMPUTER/VIDEO Mode Video ModeMenu Operation Picture Position Computer ModeTo Turn OFF the Projector Basic OperationTurning ON/OFF the Projector To Turn on the ProjectorDirect Operation Freeze Picture Function Timer FunctionDigital Zoom Function Normal Picture FunctionMenu Operation Click Button Sound AdjustmentLanguage Adjustment Main Menu Display Sound AdjustMain Menu Display Color System Video ModeColor System Select Video Source SelectPicture Image Adjustment Picture Screen Adjustment Main Menu Display Screen AdjustSelect Rear Click Button Computer System Select Computer ModePC Adjustment Computer System Display Current ModeCompatible Computer Specifications Main Menu Display Auto Image Setting Darker Brighter Main Menu Display Image AdjustDecrease Increase Lighter DeeperMain Menu Display Position Setting Picture Position AdjustmentPC Adjustment OK ? PC Adjustment Display Mode Free Picture Screen Adjustment Blue Back On or Off Other Function SettingMain Menu Display Setting Remote Control Code Change Mode 1 or ModeLamp AGE Meintenance Temperature Warning IndicatorAIR Filter Care and Cleaning AppendixLamp Replacement Lamp Replacement IndicatorLamp Cover Lamp Assembly Handle Cleaning the Lens TroubleshootingService AV Input Jacks Technical SpecificationsBoxlight