BOXLIGHT FP-95t manual Main Menu Display Image Adjust, Decrease Increase, Lighter Deeper

Page 43

COMPUTER MODE

PICTURE IMAGE ADJUSTMENT

Picture adjustments have been preset at the factory. If you want to change the setting, operate the projector as follows.

1.Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2.Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings.

3.In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the range of the levels that you can adjust are summarized in the table below.

4.Press the POINT DOWN BUTTON and a red arrow will appear.

5.Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

6.To increase the level, point the arrow to and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to and then press the SELECT (REAR CLICK) BUTTON.

7.You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, "OK ?" is displayed for confirmation.

8.Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are memorized even if the MAIN ON/OFF is switched off.

9.To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

10.If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. The settings changed remains effective until the MAIN ON/OFF switch is turned off.

11.To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, "OK ?" is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

MAIN MENU DISPLAY

IMAGE ADJUST

DISPLAY

NOTE:

The projector may not reproduce a proper image for some UXGA signals.

Since UXGA (1600 x 1200) image is converted to SXGA (1280 x 1024) image by partial scan, some lines and dots of the image do not appear.

Some video noise of flicker on this compressed UXGA image cannot be eliminated even though you try to make a Fine sync adjustment.

NOTE:

"Fine sync" and "Total dots" will be skipped when the incoming signal is digital.

TABLE OF PICTURE IMAGE ADJUSTMENT

FINE SYNC

Adjust the picture as necessary to eliminate

0

 

127

flicker from the display.

 

 

 

 

 

 

 

 

TOTAL DOTS

The number of the total dots in one horizontal period. Adjust the

 

number to match your PC image.

 

 

 

WHITE BALANCE (R/G/B)

DECREASE

0

 

63

INCREASE

 

 

 

 

 

 

 

CONTRAST

LIGHTER

0

 

63

DEEPER

 

 

 

 

 

 

 

BRIGHTNESS

DARKER

0

 

63

BRIGHTER

 

43

Image 43
Contents Boxlight To the Owner Important Safety Instructions Table of Contents Features and Design Rear of the Projector InstallationName of Each Part of the Projector Front of the ProjectorRoom Light SETTING-UP the ProjectorAdjustable Feet PositioningVentilation Moving the ProjectorExhaust Vent AIR Intake Ventrear Side Bottom Side Projector side Female AC outlet side Male Power RequirementsTerminal of the Projector Connecting the ProjectorSide of the Projector Connect the Computer Video Monitor S-VIDEO Output Jack Side of the Projector Connect the Video EquipmentVideo Input JACK-1 Video Input JACK-2Control Port Cable Removal Hint Connecting the ComputerHDB 15-PIN Terminal Connecting to the Monitor Output Terminal Analog HDB 15-PINConnecting to the Audio Monitor Output Variable Jacks Connecting to the Serial Port DB 9-PIN TerminalConnecting AN IBM-COMPATIBLE Desktop Computer Speaker L Connecting AN IBM-COMPATIBLE Laptop Computer PS/2 Port Provided Connecting a Macintosh Desktop Computer Connecting a Macintosh Powerbook Computer Connecting to the S-VHS Video Monitor Output Jack Connecting the Video EquipmentConnecting to the Audio Monitor Output Jacks Video Equipment Connecting the Video EquipmentBefore Operation Controls and IndicatorsFront Indicators TOP Controls Front Indicators TOP ControlsLamp Power Indicator Lamp Replacement IndicatorTemperature Warning Indicator Ready IndicatorWireless Remote Control Unit Operation of the Remote ControlLaser Light Window Zoom Button Timer ButtonComputer Select Button Video Select ButtonRemote Control Battery Installation 1714 Wired Remote Cable Using the Remote Control Unit wirelessDirect Operation Control the ProjectorVideo Mode COMPUTER/VIDEO ModeMenu Operation Picture Position Computer ModeTo Turn OFF the Projector Basic OperationTurning ON/OFF the Projector To Turn on the ProjectorDirect Operation Freeze Picture Function Timer FunctionDigital Zoom Function Normal Picture FunctionMenu Operation Click Button Sound AdjustmentLanguage Adjustment Main Menu Display Sound AdjustMain Menu Display Color System Video ModeColor System Select Video Source SelectPicture Image Adjustment Main Menu Display Screen Adjust Picture Screen AdjustmentSelect Rear Click Button Computer System Select Computer ModePC Adjustment Computer System Display Current ModeCompatible Computer Specifications Main Menu Display Auto Image Setting Darker Brighter Main Menu Display Image AdjustDecrease Increase Lighter DeeperMain Menu Display Position Setting Picture Position AdjustmentPC Adjustment OK ? PC Adjustment Display Mode Free Picture Screen Adjustment Blue Back On or Off Other Function SettingMain Menu Display Setting Remote Control Code Change Mode 1 or ModeLamp AGE Meintenance Temperature Warning IndicatorAIR Filter Care and Cleaning AppendixLamp Replacement Indicator Lamp ReplacementLamp Cover Lamp Assembly Handle Cleaning the Lens TroubleshootingService AV Input Jacks Technical SpecificationsBoxlight