BOXLIGHT FP-95t manual Troubleshooting, Cleaning the Lens

Page 55

APPENDIX

CLEANING THE LENS

Follow these steps to clean the projection lens:

1.Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.

Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2.Lightly wipe the cleaning cloth over the lens.

3.When you don't use the projector, replace the lens cover.

TROUBLESHOOTING

Before calling Boxlight for assistance, check the matters below once again.

1.Make sure you have connected the projector to your equipment as described in section "CONNECTING THE PROJECTOR" on pages 14 ~ 21.

2.Check cable connections. Verify that all computer, video and power cords are properly connected.

3.Verify that power is switched on.

4.If the projector still does not display an image, re-start the computer.

5.If the image still does not display, unplug the projector from the computer and check the computer monitor's display. The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in order of: Projector and computer)

6.If the problem still exists, check the following chart.

Problem:

Try these Solutions:

 

 

No power.

Plug the projector into an AC outlet.

 

Turn the MAIN ON/OFF switch to ON.

 

Press the POWER ON/OFF switch to ON.

 

Be sure the READY INDICATOR light is ON.

 

Wait one minute after the projector is turned OFF before turning the projector

 

back on.

 

NOTE: After pressing the POWER ON/OFF button to OFF. The projector functions

 

as indicated.

 

1. The LAMP POWER indicator will light and the READY indicator will turn off.

 

2. After one minute, the READY indicator will light green again and the projector

 

may be turned on by pressing the POWER ON/OFF button.

 

Check temperature warning indicator. If the indicator flashes red, the projector

 

cannot be turned on.

 

(See "BASIC OPERATION" section on page 32).

 

Check the projection lamp.

 

Replace the lamp cover. (Check the interlock switch inside of the lamp cover.)

 

 

Image is out of focus.

Adjust the focus.

 

Make sure the projection screen is at least 4.9' (1.5 m) from the projector.

 

Check the projection lens to see if it needs cleaning.

 

NOTE: Moving the projector from a cool temperature location to a warm

 

temperature location may result in moisture condensation on the lens. In

 

such an event, leave the projector OFF and wait until condensation

 

disappears.

 

 

55

Image 55
Contents Boxlight To the Owner Important Safety Instructions Table of Contents Features and Design Rear of the Projector InstallationName of Each Part of the Projector Front of the ProjectorRoom Light SETTING-UP the ProjectorAdjustable Feet PositioningVentilation Moving the ProjectorExhaust Vent AIR Intake Ventrear Side Bottom Side Projector side Female AC outlet side Male Power RequirementsTerminal of the Projector Connecting the ProjectorSide of the Projector Connect the Computer Video Monitor S-VIDEO Output Jack Side of the Projector Connect the Video EquipmentVideo Input JACK-1 Video Input JACK-2Control Port Cable Removal Hint Connecting the ComputerHDB 15-PIN Terminal Connecting to the Monitor Output Terminal Analog HDB 15-PINConnecting to the Audio Monitor Output Variable Jacks Connecting to the Serial Port DB 9-PIN TerminalConnecting AN IBM-COMPATIBLE Desktop Computer Speaker L Connecting AN IBM-COMPATIBLE Laptop Computer PS/2 Port Provided Connecting a Macintosh Desktop Computer Connecting a Macintosh Powerbook Computer Connecting to the S-VHS Video Monitor Output Jack Connecting the Video EquipmentConnecting to the Audio Monitor Output Jacks Video Equipment Connecting the Video EquipmentBefore Operation Controls and IndicatorsFront Indicators TOP Controls Front Indicators TOP ControlsLamp Power Indicator Lamp Replacement IndicatorTemperature Warning Indicator Ready IndicatorWireless Remote Control Unit Operation of the Remote ControlLaser Light Window Zoom Button Timer ButtonComputer Select Button Video Select ButtonRemote Control Battery Installation 1714 Wired Remote Cable Using the Remote Control Unit wirelessDirect Operation Control the ProjectorVideo Mode COMPUTER/VIDEO ModeMenu Operation Picture Position Computer ModeTo Turn OFF the Projector Basic OperationTurning ON/OFF the Projector To Turn on the ProjectorDirect Operation Freeze Picture Function Timer FunctionDigital Zoom Function Normal Picture FunctionMenu Operation Click Button Sound AdjustmentLanguage Adjustment Main Menu Display Sound AdjustMain Menu Display Color System Video ModeColor System Select Video Source SelectPicture Image Adjustment Main Menu Display Screen Adjust Picture Screen AdjustmentSelect Rear Click Button Computer System Select Computer ModePC Adjustment Computer System Display Current ModeCompatible Computer Specifications Main Menu Display Auto Image Setting Darker Brighter Main Menu Display Image AdjustDecrease Increase Lighter DeeperMain Menu Display Position Setting Picture Position AdjustmentPC Adjustment OK ? PC Adjustment Display Mode Free Picture Screen Adjustment Blue Back On or Off Other Function SettingMain Menu Display Setting Remote Control Code Change Mode 1 or ModeLamp AGE Meintenance Temperature Warning IndicatorAIR Filter Care and Cleaning AppendixLamp Replacement Indicator Lamp ReplacementLamp Cover Lamp Assembly Handle Cleaning the Lens TroubleshootingService AV Input Jacks Technical SpecificationsBoxlight