BenQ MP721C user manual Remote control effective range, Replacing the remote control battery

Page 15

Remote control effective range

Infra-Red (IR) remote control sensors are located on the front and the back of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 6 meters (~ 20 feet).

Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam.

•Operating the projector from the front

•Operating the projector from the rear

 

 

 

 

 

 

 

 

°

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

x

 

 

 

 

 

 

ro

 

 

 

 

 

 

p

 

 

 

 

A

 

p

 

 

 

 

 

p

A

 

 

 

 

 

 

 

pr

 

 

 

 

 

 

 

 

ox. 1

5°

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replacing the remote control battery

1.Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm whilst pulling out the battery holder.

2. Insert the new battery in the holder. Note the positive polarity should face outward.

3.Push the holder into the remote control.

• Avoid excessive heat and humidity.

•There may be battery damage if the battery is incorrectly replaced.

•Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used battery according to the battery manufacturer’s instructions.

•Never throw a battery into a fire. There may be danger of an explosion.

•If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

Introduction 11

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Welcome Disclaimer CopyrightTable of contents Iv Table of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Future reference Projector lamp is onSafety Instructions 10000 Feet Important safety instructions Bedding or any other soft surfaceAllow at least 50 cm clearance from walls Safety Instructions Projector features IntroductionIntroduction Shipping contents Lower/side view Projector exterior viewFront/upper side Rear sideControls and functions ProjectorTurns the projector on or off Freeze Remote controlAdjusts the focus of the projected image Exit3Left, Right4 Enters presentation timer setting directlyPush the holder into the remote control Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connection Wireless connection optionalConnecting a computer or monitor Projector with the wireless moduleCable VGA toConnecting a monitor Better video quality Connecting Video source devicesConnecting Audio Best video qualityConnecting a Component Video source device DVI cables To connect the projector to an S-Video source device Connecting an S-Video source deviceConnecting a composite Video source device Operation Start upOperation Utilizing the password function Setting a passwordLeft 3 or Right4 If you forget the password Entering the password recall procedureChanging the password Switching input signal Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone For example Selecting the aspect ratioPC Signal Input Selecting a picture modeHiding the image Creating your own startup screen MyScreen functionYou can set the blank time Click MyScreen to begin download To execute MyScreen utilityIcon Ii.Click Next Iii. Click NextActivating panel key lock Vi. Click Close when the window below displaysFreezing the image Setting the presentation timerPress and hold BLANK/Q? on the projector for 3 seconds Utilizing FAQ functionDisconnect the power cord from the wall socket Shutting down the projectorMenu system Menu operationUsing the menus Picture menu Color TintSharpness Pro-Picture menu Setting menu Advanced menu Auto Off Mode offTimer High AltitudeLamp Hour System ResolutionInformation menu EquivalentCare of the projector MaintenanceNew lamp should be fitted to avoid Install a new lamp for optimal performanceLamp information Calculation of lamp hourReplacing the lamp Locators on the projector Maintenance Remove the lamp cover from the projectorRemove the lamp cords from the slots Restart the projector Temperature informationResetting the lamp counter Tighten the screw that secures the lampIllustration IndicatorsStand-by mode Powering upLight Status & Description Power Temp Lamp Thermal events You do not remember the password TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputMm W x 94 mm H x 219.5 mm D 278 64.3 Unit mm Specifications DimensionsLimited warranty WarrantyMIC statement Regulation statementsFCC statement EEC statement
Related manuals
Manual 1 pages 55.09 Kb

MP721C specifications

The BenQ MP721C is a versatile and reliable multimedia projector designed to meet the needs of various presentation environments, making it an ideal choice for both educational and business settings. With a bright output and an array of features, the MP721C enhances the viewing experience, ensuring that every detail is clear and impactful.

One of the standout features of the BenQ MP721C is its impressive brightness level, measuring at 2400 ANSI lumens. This high lumen output means that the projector can be used effectively in well-lit rooms without sacrificing image quality. The resolution of 1024 x 768 (XGA) allows for crisp and clear images, making it suitable for displaying detailed presentations, videos, and graphics.

The MP721C employs DLP technology, known for its reliability and consistent performance. This technology also contributes to the projector's ability to produce rich colors and deep blacks, enhancing the overall visual experience. Furthermore, the BenQ MP721C includes a built-in speaker that offers decent audio, so users can deliver presentations without the need for external sound systems.

The connectivity options of the MP721C are robust, featuring multiple input ports such as VGA, composite video, and S-Video, ensuring compatibility with a wide range of devices including laptops, cameras, and DVD players. Additionally, the projector includes USB connectivity, allowing users to display images directly from USB drives.

The projector is designed with user convenience in mind. It offers features such as automatic vertical keystone correction, which helps to eliminate image distortion when the projector is not perfectly aligned with the screen. The easy-to-use on-screen menu simplifies the process of adjusting settings, making it accessible for presenters of all technical skill levels.

Moreover, the BenQ MP721C is energy-efficient, with a long lamp life that can reach up to 4000 hours in economic mode, reducing maintenance costs and downtime. Its compact and portable design makes it easy to transport, allowing for quick setup in different locations.

In summary, the BenQ MP721C is an adaptable projector, combining brightness, connectivity, and user-friendly features. Whether in the classroom or a boardroom, it provides an effective solution for making presentations stand out, while ensuring reliability and longevity for regular use.
Top Page Image Contents