BenQ MP721C user manual Utilizing FAQ function, Shutting down the projector

Page 40

Utilizing FAQ function

Press and hold BLANK/Q? on the projector for 3 seconds

or go to Advanced > FAQ function. Possible

solutions to problems encountered by users regarding image quality, installation, special feature operation and service information are available to you. Use MENU6/ EXIT5 to select one out of these four major categories. Press Left3/Right4 for more specific questions. Then press 3Left/4Right for possible solutions. To exit, press

EXIT5.

Shutting down the projector

1.Press Power and a prompt message appears. Press Power a second time to turn the projector off.

2.The Power indicator light flashes orange and the lamp shuts down, the fans continue to run for approximately 30 seconds to cool down the projector.

To protect the lamp, the projector will not respond to any commands during the cooling process.

Are You Sure to Power Off?

Press "Power" Again to Power Off

3.Once the cooling process finishes, a "Power Off Ring Tone" will be heard.

Disconnect the power cord from the wall socket.

• Do not unplug the power cord before the projector shutdown sequence is complete or during the 30-second cooling down process.

• If the projector is not properly shut down, to protect the lamp, when you

attempt to re-start the projector, the fans

will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the Power indicator light turns orange.

36 Operation

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Welcome Copyright DisclaimerTable of contents Iv Table of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Bedding or any other soft surface 10000 Feet Important safety instructionsAllow at least 50 cm clearance from walls Safety Instructions Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper sideRear side Lower/side viewProjector Controls and functionsTurns the projector on or off Remote control Adjusts the focus of the projected imageExit FreezeEnters presentation timer setting directly 3Left, Right4Remote control effective range Replacing the remote control batteryPull out the battery holder Push the holder into the remote controlPositioning your projector Choosing a locationSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image size Positioning your projector Maximum zoom Minimum zoom Screen Center of lens Projection distance1219 1500Wireless connection optional Connecting a computer or monitorProjector with the wireless module ConnectionVGA to CableConnecting a monitor Connecting Video source devices Connecting AudioBest video quality Better video qualityConnecting a Component Video source device DVI cables Connecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device Start up OperationOperation Setting a password Utilizing the password functionLeft 3 or Right4 Entering the password recall procedure If you forget the passwordChanging the password Adjusting the projected image Switching input signalAdjusting the projection angle Fine-tuning the image size and clarity Auto-adjusting the imageCorrecting keystone Selecting the aspect ratio For exampleSelecting a picture mode PC Signal InputCreating your own startup screen MyScreen function Hiding the imageYou can set the blank time To execute MyScreen utility IconIi.Click Next Iii. Click Next Click MyScreen to begin downloadVi. Click Close when the window below displays Activating panel key lockSetting the presentation timer Freezing the imageUtilizing FAQ function Disconnect the power cord from the wall socketShutting down the projector Press and hold BLANK/Q? on the projector for 3 secondsMenu operation Menu systemUsing the menus Picture menu Tint ColorSharpness Pro-Picture menu Setting menu Advanced menu Mode off TimerHigh Altitude Auto OffResolution Information menuEquivalent Lamp Hour SystemMaintenance Care of the projectorInstall a new lamp for optimal performance Lamp informationCalculation of lamp hour New lamp should be fitted to avoidReplacing the lamp Remove the lamp cover from the projector Locators on the projector MaintenanceRemove the lamp cords from the slots Temperature information Resetting the lamp counterTighten the screw that secures the lamp Restart the projectorIndicators Stand-by modePowering up IllustrationLight Status & Description Power Temp Lamp Thermal events Troubleshooting Plug the power cord into the AC inlet onMake sure that it is switched on You do not remember the passwordSpecifications Projector specificationsTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsDimensions Mm W x 94 mm H x 219.5 mm D 278 64.3 Unit mm SpecificationsWarranty Limited warrantyRegulation statements FCC statementEEC statement MIC statement
Related manuals
Manual 1 pages 55.09 Kb

MP721C specifications

The BenQ MP721C is a versatile and reliable multimedia projector designed to meet the needs of various presentation environments, making it an ideal choice for both educational and business settings. With a bright output and an array of features, the MP721C enhances the viewing experience, ensuring that every detail is clear and impactful.

One of the standout features of the BenQ MP721C is its impressive brightness level, measuring at 2400 ANSI lumens. This high lumen output means that the projector can be used effectively in well-lit rooms without sacrificing image quality. The resolution of 1024 x 768 (XGA) allows for crisp and clear images, making it suitable for displaying detailed presentations, videos, and graphics.

The MP721C employs DLP technology, known for its reliability and consistent performance. This technology also contributes to the projector's ability to produce rich colors and deep blacks, enhancing the overall visual experience. Furthermore, the BenQ MP721C includes a built-in speaker that offers decent audio, so users can deliver presentations without the need for external sound systems.

The connectivity options of the MP721C are robust, featuring multiple input ports such as VGA, composite video, and S-Video, ensuring compatibility with a wide range of devices including laptops, cameras, and DVD players. Additionally, the projector includes USB connectivity, allowing users to display images directly from USB drives.

The projector is designed with user convenience in mind. It offers features such as automatic vertical keystone correction, which helps to eliminate image distortion when the projector is not perfectly aligned with the screen. The easy-to-use on-screen menu simplifies the process of adjusting settings, making it accessible for presenters of all technical skill levels.

Moreover, the BenQ MP721C is energy-efficient, with a long lamp life that can reach up to 4000 hours in economic mode, reducing maintenance costs and downtime. Its compact and portable design makes it easy to transport, allowing for quick setup in different locations.

In summary, the BenQ MP721C is an adaptable projector, combining brightness, connectivity, and user-friendly features. Whether in the classroom or a boardroom, it provides an effective solution for making presentations stand out, while ensuring reliability and longevity for regular use.
Top Page Image Contents