BenQ MP721C user manual If you forget the password, Entering the password recall procedure

Page 31

If you forget the password

You will be asked to enter the four digit password every time you turn on the projector. If you enter the wrong password, the password error message displays. You can retry by pressing Up 5, or if you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure.

Password Error

Try again

Forgot password, please refer to User's manual

Entering the password recall procedure

Press and hold Right4on the projector for 3 seconds. The projector will display 4 sets of coded number on the screen. Write down the number and turn off your projector. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

Changing the password

1.Open the on-screen menu and go to Setting > Change Password.

2.Press Left 3or Right4.

3.Enter the old password.

i.If the password is correct, you can go on to enter new password.

ii.If the password is incorrect, a “Password Error” message displays. Press Up 5 to try again or press Down 6 to cancel.

4.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __

Keep this manual in a safe place.

5.Perform one of the following 3 steps.

i.Press AUTO to confirm.

ii.Press Up 5 to try again.

iii.Press Down 6 to cancel the set-up and return to the on-screen menu.

6.Confirm the new password by re-entering the new password.

7.Perform one of the following 3 steps.

i.Pressing AUTO completes the procedure.

ii.Press Up 5 to try again.

iii.Press Down 6 to cancel the set-up and return to the on-screen menu.

Operation 27

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Welcome Disclaimer CopyrightTable of contents Iv Table of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Future reference Projector lamp is onSafety Instructions Bedding or any other soft surface 10000 Feet Important safety instructionsAllow at least 50 cm clearance from walls Safety Instructions Introduction Projector featuresIntroduction Shipping contents Lower/side view Projector exterior viewFront/upper side Rear sideProjector Controls and functionsTurns the projector on or off Freeze Remote controlAdjusts the focus of the projected image Exit3Left, Right4 Enters presentation timer setting directlyPush the holder into the remote control Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connection Wireless connection optionalConnecting a computer or monitor Projector with the wireless moduleCable VGA toConnecting a monitor Better video quality Connecting Video source devicesConnecting Audio Best video qualityConnecting a Component Video source device DVI cables To connect the projector to an S-Video source device Connecting an S-Video source deviceConnecting a composite Video source device Start up OperationOperation Setting a password Utilizing the password functionLeft 3 or Right4 Entering the password recall procedure If you forget the passwordChanging the password Adjusting the projected image Switching input signalAdjusting the projection angle Fine-tuning the image size and clarity Auto-adjusting the imageCorrecting keystone For example Selecting the aspect ratioPC Signal Input Selecting a picture modeCreating your own startup screen MyScreen function Hiding the imageYou can set the blank time Click MyScreen to begin download To execute MyScreen utilityIcon Ii.Click Next Iii. Click NextActivating panel key lock Vi. Click Close when the window below displaysFreezing the image Setting the presentation timerPress and hold BLANK/Q? on the projector for 3 seconds Utilizing FAQ functionDisconnect the power cord from the wall socket Shutting down the projectorMenu system Menu operationUsing the menus Picture menu Tint ColorSharpness Pro-Picture menu Setting menu Advanced menu Auto Off Mode offTimer High AltitudeLamp Hour System ResolutionInformation menu EquivalentCare of the projector MaintenanceNew lamp should be fitted to avoid Install a new lamp for optimal performanceLamp information Calculation of lamp hourReplacing the lamp Remove the lamp cover from the projector Locators on the projector MaintenanceRemove the lamp cords from the slots Restart the projector Temperature informationResetting the lamp counter Tighten the screw that secures the lampIllustration IndicatorsStand-by mode Powering upLight Status & Description Power Temp Lamp Thermal events You do not remember the password TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputMm W x 94 mm H x 219.5 mm D 278 64.3 Unit mm Specifications DimensionsLimited warranty WarrantyMIC statement Regulation statementsFCC statement EEC statement
Related manuals
Manual 1 pages 55.09 Kb

MP721C specifications

The BenQ MP721C is a versatile and reliable multimedia projector designed to meet the needs of various presentation environments, making it an ideal choice for both educational and business settings. With a bright output and an array of features, the MP721C enhances the viewing experience, ensuring that every detail is clear and impactful.

One of the standout features of the BenQ MP721C is its impressive brightness level, measuring at 2400 ANSI lumens. This high lumen output means that the projector can be used effectively in well-lit rooms without sacrificing image quality. The resolution of 1024 x 768 (XGA) allows for crisp and clear images, making it suitable for displaying detailed presentations, videos, and graphics.

The MP721C employs DLP technology, known for its reliability and consistent performance. This technology also contributes to the projector's ability to produce rich colors and deep blacks, enhancing the overall visual experience. Furthermore, the BenQ MP721C includes a built-in speaker that offers decent audio, so users can deliver presentations without the need for external sound systems.

The connectivity options of the MP721C are robust, featuring multiple input ports such as VGA, composite video, and S-Video, ensuring compatibility with a wide range of devices including laptops, cameras, and DVD players. Additionally, the projector includes USB connectivity, allowing users to display images directly from USB drives.

The projector is designed with user convenience in mind. It offers features such as automatic vertical keystone correction, which helps to eliminate image distortion when the projector is not perfectly aligned with the screen. The easy-to-use on-screen menu simplifies the process of adjusting settings, making it accessible for presenters of all technical skill levels.

Moreover, the BenQ MP721C is energy-efficient, with a long lamp life that can reach up to 4000 hours in economic mode, reducing maintenance costs and downtime. Its compact and portable design makes it easy to transport, allowing for quick setup in different locations.

In summary, the BenQ MP721C is an adaptable projector, combining brightness, connectivity, and user-friendly features. Whether in the classroom or a boardroom, it provides an effective solution for making presentations stand out, while ensuring reliability and longevity for regular use.
Top Page Image Contents