BenQ cp270 user manual Connecting a Component Video source device

Page 19

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with

aD-Sub type connector) to the D-SUB/COMP. IN socket on the projector. The final connection path should be like that shown in the following diagram:

AV device

Component Video to

VGA (D-Sub) adaptor cable

If the selected video image is not displayed after the projector is turned on and the correct

video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 19

Image 19

Contents CP270 Digital Projector WelcomeTable of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Future reference Projector lamp is onSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Introduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewProjector Controls and functionsRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Front Table Set Rear Table in the System Setup Basic ProjectorPositioning your projector Choosing a locationObtaining a preferred projected image size Page Projection dimensions Connection Connecting a computerConnection To connect the projector to a notebook or desktop computerLeast video quality Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceAV device Component Video to VGA D-Sub adaptor cable To connect the projector to an S-Video source device Connecting an S-Video source deviceAV device Video cable To connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationOperation Use / to highlight the System Setup Basic menu Using the menusSecurity Settings Utilizing the password functionSetting a password If you forget the passwordEnter a new password Entering the password recall procedureChanging the password Disabling the password functionAdjusting the projected image Switching input signalAdjusting the projection angle Fine-tuning the image size and clarity Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAt the bottom of the image About the aspect ratio Selecting the aspect ratioUse of the screen without altering the images aspect Ratio Video input signals S-Video, Video, D-Sub / Comp. YPbPr Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp. analog RGBAdjusting Brightness Using Wall ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHiding the image To cancel the timer, perform the following stepsHow to use the Timer On key? Or go to the System Setup Basic PanelBased on the information you want to know Press Mode/Enter Utilizing FAQ functionFreezing the image Information menuOperating in a high altitude environment To activate the High Altitude ModeSystem Setup Advanced menu is To highlight High Altitude ModeShutting down the projector Menu system Menu operationMain menu Sub-menu Options Advanced Lamp mode Normal/EconomicLamp Settings BasicDescription of each menu Timer Picture menu Source 4. System Setup Basic menumenuColor Temperature Save SettingsPanel Key Blank TimerSleep Timer SettingsInformation menu Reset AllFAQ-Image Installation Features ServiceCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenancePage Tighten the screws that secure the lamp Cover Resetting the lamp timerSetup Advanced Lamp Settings menu Displays. Press to highlight Reset lampIndicators Troubleshooting Projector specifications SpecificationsSupported timing for PC input DimensionsTiming chart Resolution ModeHorizontal Signal FormatSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statement