BenQ cp270 Information menu, Baud Rate, Reset All, FAQ-Image Installation, Features Service

Page 44

Advanced	5. SYSTEM
menu	SETUP:

6. INFORMATION menu

	FUNCTION	DESCRIPTION (default setting/value)
	(default setting/	DESCRIPTION (default setting/value)
	value)
	Baud Rate	Selects a baud rate that is identical with your computer’s so that you
	Baud Rate	can connect the projector using a suitable RS-232 cable and update or
	(115200)	download the projector’s firmware. This function is intended for
		qualified service personnel.
	Reset All	Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Position, Phase, H. Size,
	Settings
	Settings	User 1, User 2, Language, Projector Position, High Altitude
		Mode, Security Settings, Baud Rate.
	FAQ-Image
	and
	Installation	Displays possible solutions to problems you may encounter.
	FAQ-	Displays possible solutions to problems you may encounter.
	FAQ-
	Features and
	Service
		Source
		Shows the current signal source.
		Picture Mode
	Current	Shows the selected mode in the PICTURE menu.
	Current	Resolution
	System	Resolution
	System	Shows the native resolution of the input signal.
	Status	Shows the native resolution of the input signal.
	Status	Color System
		Color System
		Shows input system format, NTSC, PAL, SECAM, or RGB.
		Equivalent Lamp Hour
		Displays the number of hours the lamp has been used.

44 Operation

Image 44

Contents Welcome CP270 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper sideControls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Set Rear Table in the System Setup Basic Projector Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Projection dimensions Connecting a computer ConnectionTo connect the projector to a notebook or desktop computer ConnectionConnecting Video source devices Best video qualityBetter video quality Least video qualityAV device Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device AV device Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Connecting a composite Video source device To connect the projector to a composite Video source deviceOperation OperationStarting up the projector Using the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Security SettingsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordAdjusting the projection angle Switching input signalAdjusting the projected image Auto-adjusting the image Fine-tuning the image size and clarityAt the bottom of the image Magnifying and searching for detailsCorrecting keystone Use of the screen without altering the images aspect Ratio Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrUsing Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightTo cancel the timer, perform the following steps How to use the Timer On key?Or go to the System Setup Basic Panel Hiding the imageUtilizing FAQ function Freezing the imageInformation menu Based on the information you want to know Press Mode/EnterTo activate the High Altitude Mode System Setup Advanced menu isTo highlight High Altitude Mode Operating in a high altitude environmentShutting down the projector Main menu Sub-menu Options Menu operationMenu system Lamp mode Normal/Economic Lamp SettingsBasic AdvancedDescription of each menu Picture menu Source 4. System Setup Basic menumenu Color TemperatureSave Settings TimerBlank Timer Sleep TimerSettings Panel KeyReset All FAQ-Image InstallationFeatures Service Information menuMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screws that secure the lamp CoverIndicators Troubleshooting Specifications Projector specificationsDimensions Timing chartResolution Mode Supported timing for PC inputSignal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive