BenQ cp270 user manual Connecting an S-Video source device, AV device Video cable

Page 20

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEOsocket on the projector. The final connection path should be like that shown in the following diagram:

AV device

S-Video cable

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 18 for details.

20 Connection

Image 20

Contents Welcome CP270 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper sideControls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Set Rear Table in the System Setup Basic Projector Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Projection dimensions Connecting a computer ConnectionTo connect the projector to a notebook or desktop computer ConnectionConnecting Video source devices Best video qualityBetter video quality Least video qualityAV device Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device AV device Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Connecting a composite Video source device To connect the projector to a composite Video source deviceOperation OperationStarting up the projector Using the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Security SettingsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordAdjusting the projection angle Switching input signalAdjusting the projected image Auto-adjusting the image Fine-tuning the image size and clarityAt the bottom of the image Magnifying and searching for detailsCorrecting keystone Use of the screen without altering the images aspect Ratio Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrUsing Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightTo cancel the timer, perform the following steps How to use the Timer On key?Or go to the System Setup Basic Panel Hiding the imageUtilizing FAQ function Freezing the imageInformation menu Based on the information you want to know Press Mode/EnterTo activate the High Altitude Mode System Setup Advanced menu isTo highlight High Altitude Mode Operating in a high altitude environmentShutting down the projector Main menu Sub-menu Options Menu operationMenu system Lamp mode Normal/Economic Lamp SettingsBasic AdvancedDescription of each menu Picture menu Source 4. System Setup Basic menumenu Color TemperatureSave Settings TimerBlank Timer Sleep TimerSettings Panel KeyReset All FAQ-Image InstallationFeatures Service Information menuMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screws that secure the lamp CoverIndicators Troubleshooting Specifications Projector specificationsDimensions Timing chartResolution Mode Supported timing for PC inputSignal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive