BenQ cp270 user manual Regulation statements, FCC statement, EEC statement, Weee directive

Page 57

Regulation statements

FCC statement

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

EEC statement

This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electronic Magnetic Compatibility) and fulfills these requirements.

WEEE directive

Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union.

This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment. For more information about recycling of this equipment, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.

Regulation statements

57

Image 57
Contents CP270 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Projector features IntroductionIntroduction Shipping contents Front/upper side Projector exterior viewProjector Controls and functionsRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Positioning your projector Set Rear Table in the System Setup Basic ProjectorChoosing a location Front TableObtaining a preferred projected image size Page Projection dimensions Connection Connecting a computerTo connect the projector to a notebook or desktop computer ConnectionBest video quality Connecting Video source devicesBetter video quality Least video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceAV device Component Video to VGA D-Sub adaptor cable Connecting an S-Video source device To connect the projector to an S-Video source deviceAV device Video cable To connect the projector to a composite Video source device Connecting a composite Video source deviceOperation Starting up the projectorOperation Use / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Security SettingsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordSwitching input signal Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Auto-adjusting the imageMagnifying and searching for details Correcting keystoneAt the bottom of the image Selecting the aspect ratio About the aspect ratioUse of the screen without altering the images aspect Ratio Picture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrFine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsOr go to the System Setup Basic Panel Hiding the imageFreezing the image Utilizing FAQ functionInformation menu Based on the information you want to know Press Mode/EnterSystem Setup Advanced menu is To activate the High Altitude ModeTo highlight High Altitude Mode Operating in a high altitude environmentShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Lamp Settings Lamp mode Normal/EconomicBasic AdvancedDescription of each menu Color Temperature Picture menu Source 4. System Setup Basic menumenuSave Settings TimerSleep Timer Blank TimerSettings Panel KeyFAQ-Image Installation Reset AllFeatures Service Information menuCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenancePage Setup Advanced Lamp Settings menu Resetting the lamp timerDisplays. Press to highlight Reset lamp Tighten the screws that secure the lamp CoverIndicators Troubleshooting Projector specifications SpecificationsTiming chart DimensionsResolution Mode Supported timing for PC inputSupported timing for Component-YPbPrinput Signal FormatSupported timing for Video and S-Video inputs HorizontalLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive