BenQ cp270 user manual This Apparatus Must be Earthed

Page 6

Safety Instructions (Continued)

17.Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

18.Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced.

Warning

•THIS APPARATUS MUST BE EARTHED.

•When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

6 Important safety instructions

Image 6

Contents Welcome CP270 Digital ProjectorTable of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper sideControls and functions ProjectorRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Choosing a location Set Rear Table in the System Setup Basic ProjectorPositioning your projector Front TableObtaining a preferred projected image size Page Projection dimensions To connect the projector to a notebook or desktop computer Connecting a computerConnection ConnectionBetter video quality Connecting Video source devicesBest video quality Least video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceAV device Component Video to VGA D-Sub adaptor cable Connecting an S-Video source device To connect the projector to an S-Video source deviceAV device Video cable Connecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorOperation Using the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Security SettingsDisabling the password function Entering the password recall procedureChanging the password Enter a new passwordSwitching input signal Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneAt the bottom of the image Selecting the aspect ratio About the aspect ratioUse of the screen without altering the images aspect Ratio PC input signals D-Sub / Comp. analog RGB Selecting a picture modePicture modes for different types of signals Video input signals S-Video, Video, D-Sub / Comp. YPbPrSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightOr go to the System Setup Basic Panel To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the imageInformation menu Utilizing FAQ functionFreezing the image Based on the information you want to know Press Mode/EnterTo highlight High Altitude Mode To activate the High Altitude ModeSystem Setup Advanced menu is Operating in a high altitude environmentShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Lamp mode Normal/EconomicLamp Settings AdvancedDescription of each menu Save Settings Picture menu Source 4. System Setup Basic menumenuColor Temperature TimerSettings Blank TimerSleep Timer Panel KeyFeatures Service Reset AllFAQ-Image Installation Information menuMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Displays. Press to highlight Reset lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Tighten the screws that secure the lamp CoverIndicators Troubleshooting Specifications Projector specificationsResolution Mode DimensionsTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Signal FormatSupported timing for Component-YPbPrinput HorizontalCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive