BenQ cp270 user manual Resetting the lamp timer, Tighten the screws that secure the lamp Cover

Page 50

10.Tighten the screws that secure the lamp

cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screws.

11.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12. After the startup logo, open the On-Screen	Notice
Display (OSD) menu. Go to the SYSTEM
	Reset Lamp Timer?
SETUP: Advanced > Lamp Settings menu.
Press Mode/Enter. The Lamp Settings page	Reset	Cancel
displays. Press to highlight Reset lamp

timer and press Mode/Enter. A warning

message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/Enter. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

50 Maintenance

Image 50

Contents Welcome CP270 Digital ProjectorTable of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper sideControls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Choosing a location Set Rear Table in the System Setup Basic ProjectorPositioning your projector Front TableObtaining a preferred projected image size Page Projection dimensions To connect the projector to a notebook or desktop computer Connecting a computerConnection ConnectionBetter video quality Connecting Video source devicesBest video quality Least video qualityAV device Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device AV device Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Connecting a composite Video source device To connect the projector to a composite Video source deviceOperation OperationStarting up the projector Using the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Security SettingsDisabling the password function Entering the password recall procedureChanging the password Enter a new passwordAdjusting the projection angle Switching input signalAdjusting the projected image Auto-adjusting the image Fine-tuning the image size and clarityAt the bottom of the image Magnifying and searching for detailsCorrecting keystone Use of the screen without altering the images aspect Ratio Selecting the aspect ratioAbout the aspect ratio PC input signals D-Sub / Comp. analog RGB Selecting a picture modePicture modes for different types of signals Video input signals S-Video, Video, D-Sub / Comp. YPbPrSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightOr go to the System Setup Basic Panel To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the imageInformation menu Utilizing FAQ functionFreezing the image Based on the information you want to know Press Mode/EnterTo highlight High Altitude Mode To activate the High Altitude ModeSystem Setup Advanced menu is Operating in a high altitude environmentShutting down the projector Main menu Sub-menu Options Menu operationMenu system Basic Lamp mode Normal/EconomicLamp Settings AdvancedDescription of each menu Save Settings Picture menu Source 4. System Setup Basic menumenuColor Temperature TimerSettings Blank TimerSleep Timer Panel KeyFeatures Service Reset AllFAQ-Image Installation Information menuMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Displays. Press to highlight Reset lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Tighten the screws that secure the lamp CoverIndicators Troubleshooting Specifications Projector specificationsResolution Mode DimensionsTiming chart Supported timing for PC inputSupported timing for Video and S-Video inputs Signal FormatSupported timing for Component-YPbPrinput HorizontalCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive

10.Tighten the screws that secure the lamp

cover.

11.Restart the projector.

Resetting the lamp timer

SETUP: Advanced > Lamp Settings menu.

displays. Press to highlight Reset lamp