BenQ MW516, MX514 Source, Volume +, Mute, Freeze, Capture, Test, Teaching Template, 22. CC

Page 13

14.Source

Displays the source selection bar. See "Switching input signal" on page 33 for details.

15.Volume +/-

Adjusts the sound level. See "Adjusting the sound" on page 43 for details.

16.Page Up/Down

Page up/down arrows when connected through USB to a PC. See "Remote paging operations" on page 41 for details.

17.Mute

Toggles projector audio between on and off.

18. Freeze

Freezes the projected image. See "Freezing the image" on page 42 for details.

19.Capture

Captures current displayed screen to be MyScreen. See "Creating your own startup screen" on page 39 for details.

20.Test

Displays the test pattern. See "Use build-in test pattern" on page 27.

21.Teaching Template

Displays the selectable bar for teachers choosing the template as his/her suitable teaching background. See "Use Teaching Template" on page 44.

22.CC

Display the video term description on screen which is provided for hard-of- hearing viewers.

Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 15 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam.

•Operating the projector from the front

Introduction 13

Image 13

Contents User Man ual Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Source Volume +Mute FreezeReplacing the remote control battery Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Page Max length Set mm Inch Max. zoom Age Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices To connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Utilizing the password function Using a security cable lockSetting a password Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall Color3D Color Management Selecting a Color TemperaturePress MODE/ENTER and the 3D Color Management page displays Creating your own startup screen Go to the System Setup Basic MyScreen menu, press MODE/ENTERTop-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsRemote paging operations Freezing the image Hiding the imageAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Until the System Setup Advanced menu is highlighted Select the lamp saver mode100% dynamically by detecting the content brightness level Personalizing the projector menu displayShutting down the projector Menu system Menu operationSystem ION Description of each menu Invert 3D SyncTeaching TemplatePicture menu Picture ModeReference ModeMenu 3D Color Management Save Settings Quick Auto TemperatureBrilliant SearchSettings TimerPresentation LanguageOperation System Setup Basic menuPanel Key LockHigh Altitude System Setup Advanced menuAudio LampClosed Reset AllCaption StandbyCurrent Information menuSystem StatusCare of the projector MaintenanceLamp information Setting Auto Power OffGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Off IndicatorsOff Red Troubleshooting Optical SpecificationsCeiling mount installation Dimensions232.5 123.4 301.7 68.3 71.2Supported timing for PC input Timing chartSupported timing for Hdmi input Resolution Horizontal Vertical Pixel Mode Frequency KHz MHzSupported timing for Component-YPbPrinput Patents for MS513/MX514/MW516 Warranty and Copyright information