BenQ MX514, MW516 user manual Magnifying and searching for details, Selecting the aspect ratio

Page 34

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

Using the remote control

1.

Press Digital Zoom +/- to display the Zoom

 

bar.

 

 

2.

Press Digital Zoom + to magnify the center

 

of the picture. Press the key repeatedly until

 

the picture size is suitable for your need.

 

3.

Use the directional arrows ( , ,

,

)

 

on the projector or remote control to

 

 

 

navigate the picture.

 

 

4.

To restore the picture to its original size,

 

 

press AUTO. You can also press Digital

 

 

Zoom -. When the key is pressed again, the

 

picture is further reduced until it is restored to the original size.

Using the OSD menu

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.

3.Repeat steps 2-4 in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps.

4.Press on the projector repeatedly to magnify the picture to a desired size.

5.To navigate the picture, press MODE/ENTER to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture.

6.Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

7.To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/ out functionality, and press AUTO to restore the picture to its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio,and digital TV and DVDs are usually in 16:9 or 16:10 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected image ratio (no matter what aspect the source is):

Using the remote control

1.Press ASPECT to show the current setting.

2.Press ASPECT repeatedly to select an aspect ratio to suit the format of the video signal and your display requirements.

Using the OSD menu 34 Operation

Image 34
Contents User Man ual Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Mute Volume +Source FreezeReplacing the remote control battery Front Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size Page Projection dimensions Max length Set mm Inch Max. zoom Age Min. zoomConnection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting an Hdmi source device To connect the projector to an Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Setting a password Using a security cable lockUtilizing the password function Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modes3D Color Management Selecting a Color TemperaturePress MODE/ENTER and the 3D Color Management page displays Go to the System Setup Basic MyScreen menu, press MODE/ENTER Creating your own startup screenSetting the presentation timer Top-Left Bottom-Left Top-Right Bottom-RightHow to use the Timer On key? To cancel the timer, perform the following stepsRemote paging operations Hiding the image Freezing the imageTo activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentUse Teaching Template 100% dynamically by detecting the content brightness level Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Personalizing the projector menu displayShutting down the projector Menu operation Menu systemSystem ION Description of each menu Teaching 3D SyncInvert TemplateReference Picture ModePicture menu ModeBrilliant TemperatureMenu 3D Color Management Save Settings Quick Auto SearchPresentation TimerSettings LanguagePanel Key System Setup Basic menuOperation LockAudio System Setup Advanced menuHigh Altitude LampCaption Reset AllClosed StandbySystem Information menuCurrent StatusMaintenance Care of the projectorGetting to know the lamp hour Setting Auto Power OffLamp information Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Off IndicatorsOff Red Troubleshooting Specifications Optical232.5 123.4 DimensionsCeiling mount installation 301.7 68.3 71.2Timing chart Supported timing for PC inputResolution Horizontal Vertical Pixel Mode Frequency KHz MHz Supported timing for Hdmi inputSupported timing for Component-YPbPrinput Warranty and Copyright information Patents for MS513/MX514/MW516