BenQ MW516, MX514 user manual Personalizing the projector menu display, Select the lamp saver mode

Page 45

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.

•Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time

length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.

•Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position.

•Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language.

•Reminder Message in the SYSTEM SETUP: Advanced > Menu Settings menu

sets whether to display reminder messages on screen. Use / to select your desired setting.

•Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen.

Select the lamp saver mode

•Using the remote control.

Press Smart Eco and Highlight Lamp mode and press / to select Normal/ Economic/Smart Eco.

•Using the OSD menu.

1.Press Menu/Exit and then press /

until the SYSTEM SETUP: Advanced menu is highlighted.

2. Press to highlight Lamp mode and press

Mode/Enter. The Lamp Settings page displays.

3.Highlight Lamp mode and press / to select Normal/Economic/Smart Eco. The lamp brightness vary from the different lamp mode,see the description list

in table below.

	Lamp mode	Description
	Normal	100% lamp brightness.

	Economic	80% lamp power consumption.

	Smart Eco	This is default setting. Lamp power consumption will save from 30% to
	Smart Eco	100% dynamically by detecting the content brightness level.
		100% dynamically by detecting the content brightness level.

If the Economic mode is selected, the light output will be reduced and result in darker projected pictures.

Operation 45

Image 45

Contents User Man ual Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Source Volume +Mute FreezeReplacing the remote control battery Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Page Max length Set mm Inch Max. zoom Age Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices To connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Utilizing the password function Using a security cable lockSetting a password Securing the projectorIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorSelecting a Color Temperature 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Creating your own startup screen Go to the System Setup Basic MyScreen menu, press MODE/ENTERTop-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps How to use the Timer On key?Remote paging operations Freezing the image Hiding the imageAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Until the System Setup Advanced menu is highlighted Select the lamp saver mode100% dynamically by detecting the content brightness level Personalizing the projector menu displayShutting down the projector Menu system Menu operationSystem ION Description of each menu Invert 3D SyncTeaching TemplatePicture menu Picture ModeReference ModeMenu 3D Color Management Save Settings Quick Auto TemperatureBrilliant SearchSettings TimerPresentation LanguageOperation System Setup Basic menuPanel Key LockHigh Altitude System Setup Advanced menuAudio LampClosed Reset AllCaption StandbyCurrent Information menuSystem StatusCare of the projector MaintenanceLamp information Setting Auto Power OffGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Indicators OffOff Red Troubleshooting Optical SpecificationsCeiling mount installation Dimensions232.5 123.4 301.7 68.3 71.2Supported timing for PC input Timing chartSupported timing for Hdmi input Resolution Horizontal Vertical Pixel Mode Frequency KHz MHzSupported timing for Component-YPbPrinput Patents for MS513/MX514/MW516 Warranty and Copyright information