BenQ MX514, MW516 user manual Connecting an S-Video/composite source device

Page 24

Connecting an S-Video/composite source device

Examine your Video source device to determine if it has an unused S-Video/composite output jack available:

•If it has both jacks, use the S-Video output jack for connection as the S-Video terminal provides better picture quality than the Video terminal.

•If it has either of the output jack, you can also continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video/Video source device:

1.Take an S-Video/Video cable and connect one end to the S-Video/Video output jack of the Video source device.

2.Connect the other end of the S-Video/Video cable to theS-Video/ Video jack on the projector.

3.If you wish to make use of the projector speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

24 Connection

Image 24

Contents User Man ual Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Volume + SourceMute FreezeReplacing the remote control battery Positioning your projector Choosing a locationFront Table Front CeilingObtaining a preferred projected image size Page Projection dimensions Max length Set mm Inch Max. zoom Age Min. zoomConnection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting an Hdmi source device To connect the projector to an Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Using a security cable lock Utilizing the password functionSetting a password Securing the projectorIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Setting the User 1/User 2 modeGo to the Picture Picture Mode menu Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesSelecting a Color Temperature 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Go to the System Setup Basic MyScreen menu, press MODE/ENTER Creating your own startup screenSetting the presentation timer Top-Left Bottom-Left Top-Right Bottom-RightTo cancel the timer, perform the following steps How to use the Timer On key?Remote paging operations Hiding the image Freezing the imageAdjusting the sound Adjusting the sound levelTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Select the lamp saver mode Until the System Setup Advanced menu is highlighted100% dynamically by detecting the content brightness level Personalizing the projector menu displayShutting down the projector Menu operation Menu systemSystem ION Description of each menu 3D Sync InvertTeaching TemplatePicture Mode Picture menuReference ModeTemperature Menu 3D Color Management Save Settings Quick AutoBrilliant SearchTimer SettingsPresentation LanguageSystem Setup Basic menu OperationPanel Key LockSystem Setup Advanced menu High AltitudeAudio LampReset All ClosedCaption StandbyInformation menu CurrentSystem StatusMaintenance Care of the projectorSetting Auto Power Off Lamp informationGetting to know the lamp hour Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators OffOff Red Troubleshooting Specifications OpticalDimensions Ceiling mount installation232.5 123.4 301.7 68.3 71.2Timing chart Supported timing for PC inputResolution Horizontal Vertical Pixel Mode Frequency KHz MHz Supported timing for Hdmi inputSupported timing for Component-YPbPrinput Warranty and Copyright information Patents for MS513/MX514/MW516