BenQ MW516, MX514 user manual Menu operation, Menu system

Page 47

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

Main menu	Sub-menu	Options

	Wall Color	Off/Light Yellow/Pink/Light
	Wall Color	Green/Blue/Blackboard
		Green/Blue/Blackboard
	Aspect Ratio	Auto/Real/4:3/16:9/16:10
	Keystone
	Position
	Phase

H. Size

1.Digital Zoom

	DISPLAY
	DISPLAY	3D Sync		Off/Top-Bottom/Frame sequential
		3D Sync Invert		On/Off
				Off/Letter Formation/Musical
			Blackboard	Staff/Worksheet/Coordinate
		Teaching		Chart
		Template		Off/Letter Formation/Musical
			Whiteboard	Staff/Worksheet/Coordinate
				Chart

		Picture Mode	Dynamic/Presentation/sRGB/Cinema/User 1/User
		Picture Mode	2
			2
		Reference Mode Dynamic/Presentation/sRGB/Cinema
		Brightness
		Contrast
		Color
	2.	Tint
	2.	Sharpness
	PICTURE
	PICTURE	Brilliant Color		On/Off
		Color		Cool/Normal/Warm
		Temperature		Cool/Normal/Warm
		Temperature
			Primary Color	R/G/B/C/M/Y
		3D Color	Hue
		Management
		Management	Saturation
			Gain
		Save Settings
	3. SOURCE	Quick Auto Search		On/Off
	3. SOURCE	Color Space Conversion		Auto/RGB/YUV
		Color Space Conversion		Auto/RGB/YUV

Operation 47

Image 47

Contents User Man ual Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Freeze Volume +Source MuteReplacing the remote control battery Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Max length Set mm Inch Max. zoom Age Min. zoom Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting Video source devices To connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Securing the projector Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays Selecting a Color Temperature3D Color Management Creating your own startup screen Go to the System Setup Basic MyScreen menu, press MODE/ENTERTop-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerRemote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Hiding the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeUse Teaching Template Personalizing the projector menu display Select the lamp saver modeUntil the System Setup Advanced menu is highlighted 100% dynamically by detecting the content brightness levelShutting down the projector Menu system Menu operationSystem ION Description of each menu Template 3D SyncInvert TeachingMode Picture ModePicture menu ReferenceSearch TemperatureMenu 3D Color Management Save Settings Quick Auto BrilliantLanguage TimerSettings PresentationLock System Setup Basic menuOperation Panel KeyLamp System Setup Advanced menuHigh Altitude AudioStandby Reset AllClosed CaptionStatus Information menuCurrent SystemCare of the projector MaintenanceExtending lamp life Setting Auto Power OffLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Off Red IndicatorsOff Troubleshooting Optical Specifications301.7 68.3 71.2 DimensionsCeiling mount installation 232.5 123.4Supported timing for PC input Timing chartSupported timing for Hdmi input Resolution Horizontal Vertical Pixel Mode Frequency KHz MHzSupported timing for Component-YPbPrinput Patents for MS513/MX514/MW516 Warranty and Copyright information