BenQ W10000/W9000 Using the menus, W10000-en.book Page 25 Thursday, October 19, 2006 145 PM

Page 25

W10000-en.book Page 25 Thursday, October 19, 2006 1:45 PM

Advance

Advanced - 20 step IRIS Whisper mode

Edge Optimizing

Clarity Control

White Balance Fine Tuning

3D Color Management

Color Temp. Info.

RGB Gain

RGB Offset

Store Color Temp To User1

Store Color Temp To User2

Primary Color Intensity Hue Saturation

Store to Favorite Color 1 Store to Favorite Color 2 Store to Favorite Color 3 Load Default Color Space

User 1

User 2

Lamp Native

Warm

Normal

Cool

Red Gain

Green Gain

Blue Gain

Red Offset

Green Offset

Blue Offset

Red

Yellow

Green

Cyan

Blue

Magenta

English

Using the menus

The projector is equipped with on-screen display (OSD) menus for making various adjustments and settings.

There are eight different menu languages. See page 24 for more details.

23

1

ENTER

C T

The following example describes the adjustment of the keystone.

1.Press the MENU/EXIT button to display the OSD menu. 4. Adjust keystone values by pressing e or f.

2.Use e or f to select Setup and press SOURCE/ENTER.

3.Use c or d to select Keystone.

5.Press the MENU/EXIT button twice* to leave and save the settings.

*The first press leads you back to the submenu and the second press closes the on-screen menu.

Menus 25

Image 25
Contents W10000/W9000 Digital Projector Home Cinema Series WelcomeCopyright WarrantyDisclaimer Table of contents Using the menus Picture menu Display menu Fine-tuning the image size and claritySetup menu Advance menu IndicatorsSafety, regulatory and legal information Safety instructions Safety instructionsLamp assembly for replacement Areas where the mains power supplyDo not block the ventilation holes whilst During operation. It may harm your sightW10000-en.book Page 8 Thursday, October 19, 2006 145 PM Remote control batteries Shipping contentsOverview Full HD compatibile BenQ W10000/W9000 projector featuresProjector exterior view Connector panelFront and upper side view Rear viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorFloor front Floor rearWidescreen ratio screen dimension table Installation for a 169 ratio screenObtaining a preferred projected image size Diagonal Width Height Min distance withStandard ratio screen dimension table Installation for a 43 ratio screenShifting the projection lens vertically Connecting a computer Connecting with video equipmentConnect the projector to a computer with a VGA-BNC cable Connecting Hdmi devices Connecting video inputsConnecting component-video devices Connecting S-video or video devicesAdjusting the projected image Using the projectorPreparations Turning the projector onSelecting a preset mode Fine-tuning the image size and clarityOptimizing the image Selecting the aspect ratioWith letterbox format to Adjusting contrast ratioDisplaying more than one image source simultaneously Other adjustmentsPOP Personalizing the projector menu display Turning the power offSaving and loading the video memory On Screen Display OSD structure MenusW10000-en.book Page 25 Thursday, October 19, 2006 145 PM Using the menusPicture menu Extended Picture SettingsOptions menu Display menuAdvance menu Setup menuLamp Dust FilterIv. Repeat steps ii and iii for other color adjustments To adjust and store the settingsCare of the projector Additional informationFilter timer. See page 28 for details To clean the filterRemove the filter cover by gently lifting Outwards and away from the projectorTo install the cover Installing the cable connector-panel coverSection. See page 31 for details Both sides. Loosen the screwsTighten the screws securing the lamp box Replacing the lampWhen the projector is in a normal state IndicatorsWhen the projector is in an abnormal state Projector does TroubleshootingImage is unstable Picture is blurredDimensions Specifications