BenQ W10000/W9000 user manual Picture menu, Extended Picture Settings

Page 26

W10000-en.book Page 26 Thursday, October 19, 2006 1:45 PM

English

Picture menu

The Picture menu allows you to adjust the finer details of the projected image quality.

Before making adjustments, you are suggested to choose a desired preset mode in this menu which has set some certain values in order to meet different lighting environment and presentation purposes.

1.Contrast: Adjusts the degree of difference between dark and light in the image. The higher the value, the greater the contrast.

 

 

 

-30

 

 

 

50

 

 

 

+70

2.Brightness: Adjusts the brightness of the image. The higher the value, the brighter the image. And lower the value, the darker the image. Adjust this control so the black areas of the

image appear as black and that detail in the dark areas is

visible.

 

 

 

-30

 

 

50

 

 

+70

 

 

 

 

 

 

 

 

 

 

3.Color: Increase or decrease the color intensity of the image. The higher the value, the more vivid and brighter the color.

4.Tint: Adjusts the color tones of the image. The higher the value, the more greenish the picture becomes. The lower the value, the more purplish the picture becomes.

5.Filter: Turn the video and data filters on or off. Filters can reduce noise in the picture to produce a sharper image. The higher the setting, the less the noise.

6.Sharpness: Adjusts the picture sharpness. The higher the value, the sharper the picture.

7.Preset Mode: Preset modes are provided so you can optimize your projector image set-up to suit your program type. See page 20 for more information.

8.Extended Picture Settings

Color Temp.: You can choose a preferred color temperature from among User 1, User 2, Lamp Native, Warm, Normal, and Cool. See page 29 for details about storing the Color Temperature User 1 and 2.

Color Enhancement

Red: Adjusts red hues independently.

The higher the setting, the greater the intensity of red color in the image.

Green: Adjusts green hues independently.

The higher the setting, the greater the intensity of green color in the image.

Blue: Adjusts blue hues independently.

The higher the setting, the greater the intensity of blue color in the image.

Yellow: Adjusts yellow hues independently.

The higher the setting, the greater the intensity of yellow color in the image.

White: Adjusts white peaking.

Favorite Color Loading: Loads your favorite color from Favorite Color 1, 2, 3 or Default Color Space. The settings for Favorite Color 1, 2, or 3 are made in the Advance > 3D Color Management menu. See page 29 for details about operation on setting the picture color quality.

9.Save Settings: There are three video memories in which users can store settings, including all of the items in the Picture menu. Each input source can store up to 3 sets of user memories.

To store the settings:

i.) Adjusts the items in the Picture menu to desired values. ii.) Select Save Settings, press ENTER.

iii.) Select To User’s Memory 1, To User’s Memory 2, or To User’s Memory 3, and press ENTER to store the settings.

iv.) To leave the OSD, press EXIT.

10. Load Settings: Loads the settings from one of three User Memories or the default setting.

26 Menus

Image 26
Contents Welcome W10000/W9000 Digital Projector Home Cinema SeriesDisclaimer WarrantyCopyright Table of contents Setup menu Advance menu Fine-tuning the image size and clarityUsing the menus Picture menu Display menu IndicatorsSafety, regulatory and legal information Safety instructions Safety instructionsDo not block the ventilation holes whilst Areas where the mains power supplyLamp assembly for replacement During operation. It may harm your sightW10000-en.book Page 8 Thursday, October 19, 2006 145 PM Overview Shipping contentsRemote control batteries BenQ W10000/W9000 projector features Full HD compatibileFront and upper side view Connector panelProjector exterior view Rear viewControls and functions Control panelRemote control Floor front Positioning your projectorChoosing a location Floor rearObtaining a preferred projected image size Installation for a 169 ratio screenWidescreen ratio screen dimension table Diagonal Width Height Min distance withShifting the projection lens vertically Installation for a 43 ratio screenStandard ratio screen dimension table Connect the projector to a computer with a VGA-BNC cable Connecting with video equipmentConnecting a computer Connecting component-video devices Connecting video inputsConnecting Hdmi devices Connecting S-video or video devicesPreparations Using the projectorAdjusting the projected image Turning the projector onOptimizing the image Fine-tuning the image size and claritySelecting a preset mode Selecting the aspect ratioAdjusting contrast ratio With letterbox format toPOP Other adjustmentsDisplaying more than one image source simultaneously Saving and loading the video memory Turning the power offPersonalizing the projector menu display Menus On Screen Display OSD structureUsing the menus W10000-en.book Page 25 Thursday, October 19, 2006 145 PMExtended Picture Settings Picture menuDisplay menu Options menuLamp Setup menuAdvance menu Dust FilterTo adjust and store the settings Iv. Repeat steps ii and iii for other color adjustmentsAdditional information Care of the projectorRemove the filter cover by gently lifting To clean the filterFilter timer. See page 28 for details Outwards and away from the projectorSection. See page 31 for details Installing the cable connector-panel coverTo install the cover Both sides. Loosen the screwsReplacing the lamp Tighten the screws securing the lamp boxWhen the projector is in an abnormal state IndicatorsWhen the projector is in a normal state Image is unstable TroubleshootingProjector does Picture is blurredSpecifications Dimensions