BenQ W10000/W9000 user manual Indicators, When the projector is in a normal state

Page 34

W10000-en.book Page 34 Thursday, October 19, 2006 1:45 PM

English

Indicators

There are three indicators which show the status of the projector. Check the following for information about the indicator lights. If there is anything wrong, turn the projector off and contact your dealer.

When the projector is in a normal state, ...

POWER

TEMP

LAMP

STATE

REMARK

 

 

 

 

 

Orange

 

 

Standby mode.

 

Flashing

 

 

The projector is powering up.

Cannot turn the projector off.

orange

 

 

 

 

 

 

Green

 

 

The projector is under normal

 

 

 

operation.

 

 

 

 

 

 

Off

Off

(1) The projector needs 110

 

 

seconds to cool down as it

 

 

 

 

was abnormally shut down

 

Flashing

 

 

without the normal cooling

Cannot turn the projector on.

green

 

 

down process. Or

 

 

 

 

 

 

(2) The projector needs to cool

 

 

 

 

for 110 seconds after the

 

 

 

 

power is turned off.

 

When the projector is in an abnormal state, ...

POWER

TEMP

LAMP

STATE

 

REMARK

 

 

 

 

 

 

 

 

(1) The lamp has exceeded its

Solution:

Orange

Off

Red

usage life. Or

• Install a new lamp.

(2) The lamp is not properly

• Please contact your dealer for

 

 

 

 

 

 

attached or is damaged.

 

assistance.

 

 

 

 

 

Orange

Red

Off

The dust filter is seriously clogged

Solution:

with dust. The projector is going to

• Install a new filter.

 

 

 

shut down.

 

 

 

 

 

 

 

 

 

Solution:

 

 

 

The internal temperature is too

• Make sure that the ventilation

 

 

 

high.

 

holes are not blocked.

 

 

 

• The intake ventilation or the

Relocate the projector.

Orange

Red

Off

exhaust ventilation is blocked.

• Stop using the projector until

• The projector may be in a poorly

 

the ambient temperature falls

 

 

 

 

 

 

 

ventilated location.

 

within the specified range. The

 

 

 

• The ambient temperature may

 

maximum operating

 

 

 

be too high.

 

temperature is specified as 40°C

 

 

 

 

 

/ 104°F.

 

 

 

 

 

 

 

 

 

Solution:

 

 

 

 

• Check if the power supply is

Orange

Flashing

Flashing

The fans are not working.

 

stable.

red

red

• Check if there is object stuck in

 

 

 

 

 

 

 

the fans.

 

 

 

 

Contact your dealer.

 

 

 

 

 

 

34 Additional information

Image 34
Contents Welcome W10000/W9000 Digital Projector Home Cinema SeriesCopyright WarrantyDisclaimer Table of contents Setup menu Advance menu Fine-tuning the image size and clarityUsing the menus Picture menu Display menu IndicatorsSafety, regulatory and legal information Safety instructions Safety instructionsDo not block the ventilation holes whilst Areas where the mains power supplyLamp assembly for replacement During operation. It may harm your sightW10000-en.book Page 8 Thursday, October 19, 2006 145 PM Remote control batteries Shipping contentsOverview BenQ W10000/W9000 projector features Full HD compatibileFront and upper side view Connector panelProjector exterior view Rear viewControls and functions Control panelRemote control Floor front Positioning your projectorChoosing a location Floor rearObtaining a preferred projected image size Installation for a 169 ratio screenWidescreen ratio screen dimension table Diagonal Width Height Min distance withStandard ratio screen dimension table Installation for a 43 ratio screenShifting the projection lens vertically Connecting a computer Connecting with video equipmentConnect the projector to a computer with a VGA-BNC cable Connecting component-video devices Connecting video inputsConnecting Hdmi devices Connecting S-video or video devicesPreparations Using the projectorAdjusting the projected image Turning the projector onOptimizing the image Fine-tuning the image size and claritySelecting a preset mode Selecting the aspect ratioAdjusting contrast ratio With letterbox format toDisplaying more than one image source simultaneously Other adjustmentsPOP Personalizing the projector menu display Turning the power offSaving and loading the video memory Menus On Screen Display OSD structureUsing the menus W10000-en.book Page 25 Thursday, October 19, 2006 145 PMExtended Picture Settings Picture menuDisplay menu Options menuLamp Setup menuAdvance menu Dust FilterTo adjust and store the settings Iv. Repeat steps ii and iii for other color adjustmentsAdditional information Care of the projectorRemove the filter cover by gently lifting To clean the filterFilter timer. See page 28 for details Outwards and away from the projectorSection. See page 31 for details Installing the cable connector-panel coverTo install the cover Both sides. Loosen the screwsReplacing the lamp Tighten the screws securing the lamp boxWhen the projector is in a normal state IndicatorsWhen the projector is in an abnormal state Image is unstable TroubleshootingProjector does Picture is blurredSpecifications Dimensions