BenQ MS524/MS514H/MX525/MW526/TW526 Adjusting the projected image, Adjusting the projection angle

Page 19

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 adjuster foot. It changes the image height and projection angle. To adjust the projector, screw the adjuster foot to fine- tune the horizontal angle.

To retract the foot, screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 20 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the quick- release button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.

Adjust the projected image to the

2.

Sharpen the image by rotating the

size that you need using the zoom

focus ring.

ring.

Operation 19

Image 19

Contents MS524/MS514H/MX525/MW526 TW526 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsMS524/MS514H/MX525 Screen size Projection distance mm Diagonal MW526/TW526Average Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Apply 3D Settings Save 3D SettingsTeaching Template Description Fine Tuning 3D Color Picture menu Source menu Function Description Picture ModeTemperature Color TemperatureSettings System Setup Basic menu Function Description PresentationTimer InstallationScreen LockBackground Color SplashCaption System Setup Advanced menu Function DescriptionReset All ClosedSystem CurrentStatus Care of the projector MaintenanceGetting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz MAC21 Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputMHz Ntsc Supported timing for Video and S-Video inputsDisclaimer Warranty and Copyright informationLimited warranty Copyright