BenQ MS524/MS514H/MX525/MW526/TW526 user manual Shutting down the projector, Direct power off

Page 35

Shutting down the projector

1.Press POWER and a confirmation message will display prompting you. If you don't respond in a few seconds, the message will disappear.

2.Press POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 42 for details.

3.Once the cooling process finishes, a "Power Off

Ring Tone" will be heard. The POWER indicator light is a steady orange and fans stop. Disconnect the power cord from the power outlet.

• To turn off the power ring tone, see "Turning off the Power On/ Off Ring Tone" on page 33 for details.

•If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a

few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

•Lamp life results will vary depending on environmental conditions and usage.

Direct power off

The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes to cool down. In such cases, press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.)

Operation 35

Image 35

Contents MS524/MS514H/MX525/MW526 TW526 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableMS524/MS514H/MX525 Projection dimensionsObtaining a preferred projected image size Average MW526/TW526Screen size Projection distance mm Diagonal Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Teaching Template Description Save 3D SettingsApply 3D Settings Fine Tuning 3D Color Picture menu Source menu Function Description Picture ModeTemperature Color TemperatureSettings System Setup Basic menu Function Description PresentationTimer InstallationScreen LockBackground Color SplashCaption System Setup Advanced menu Function DescriptionReset All ClosedStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsKHz Timing chartSupported timing for PC input MAC21 Supported timing for Hdmi Hdcp inputMHz Supported timing for Component-YPbPrinputTiming Ntsc Supported timing for Video and S-Video inputsDisclaimer Warranty and Copyright informationLimited warranty Copyright