BenQ MS524/MS514H/MX525/MW526/TW526 user manual m Feet

Page 5

Safety Instructions (Continued)

13.Do not place this projector in any of the following environments.

-Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

-Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

-Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

-Locations near fire alarms

-Locations with an ambient temperature above 40°C / 104°F

-Locations where the altitudes are higher than 3000 m (10000 feet).

3000 m

(10000 feet)

0m

(0 feet)

14.Do not block the ventilation holes.

-Do not place this projector on a blanket, bedding or any other soft surface.

-Do not cover this projector with a cloth or any other item.

-Do not place inflammables near the projector.

If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

15.Always place the projector on a level, horizontal surface during operation.

-Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

16.Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

Important safety instructions

5

Image 5
Contents MS524/MS514H/MX525/MW526 TW526 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingMS524/MS514H/MX525 Projection dimensionsObtaining a preferred projected image size Average MW526/TW526Screen size Projection distance mm Diagonal Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Teaching Template Description Save 3D SettingsApply 3D Settings Temperature Picture menu Source menu Function Description Picture ModeColor Temperature Fine Tuning 3D ColorTimer System Setup Basic menu Function Description PresentationInstallation SettingsBackground LockColor Splash ScreenReset All System Setup Advanced menu Function DescriptionClosed CaptionStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsKHz Timing chartSupported timing for PC input MAC21 Supported timing for Hdmi Hdcp inputMHz Supported timing for Component-YPbPrinputTiming Ntsc Supported timing for Video and S-Video inputsLimited warranty Warranty and Copyright informationCopyright Disclaimer