BenQ MS524/MS514H/MX525/MW526/TW526 user manual Timing of replacing the lamp, Status Message

Page 48

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please consult your dealer or go to http://www.BenQ.com before installing a new lamp. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 50 for details.

The following Lamp warning displays will remind you to change the lamp.

	Status	Message

	Install a new lamp for optimal performance. If the	Notice
	projector is normally run with Economic	Notice
	projector is normally run with Economic
	selected (See "Getting to know the lamp hour" on	Order Replacement Lamp
	page 47), you may continue to operate the	Order Replacement Lamp
	page 47), you may continue to operate the	Lamp>XXXX Hours
	projector until the next hour lamp warning	Lamp>XXXX Hours
	projector until the next hour lamp warning
	appears.	Order a new lamp at www.BenQ.com
	Press MODE/ENTER to dismiss the message.	OK

	It is strongly recommended that you replace the	Notice
	lamp at this age. The lamp is a consumable item.	Notice
	lamp at this age. The lamp is a consumable item.
	The lamp brightness diminishes with use. This is	Replace Lamp Soon
	normal lamp behavior. You can replace the lamp	Replace Lamp Soon
	normal lamp behavior. You can replace the lamp
	whenever you notice that the brightness level has	Lamp>XXXX Hours
	whenever you notice that the brightness level has
	significantly diminished.	Order a new lamp at www.BenQ.com
	Press MODE/ENTER to dismiss the message.	OK
		Notice
		Replace Lamp Now
		Lamp>XXXX Hours
		Lamp usage time exceeded
		Order a new lamp at www.BenQ.com
		OK

	The lamp MUST be replaced before the projector	WARNING
	will operate normally.	WARNING
	will operate normally.	Out of Lamp Usage Time
	Press MODE/ENTER to dismiss the message.	Out of Lamp Usage Time
	Press MODE/ENTER to dismiss the message.
		Replace lamp (Refer to user manual)
		Then reset lamp timer
		Order a new lamp at www.BenQ.com
		OK

"XXXX" shown in the above messages are numbers that vary depending on different models.

48 Maintenance

Image 48

Contents MS524/MS514H/MX525/MW526 TW526 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeMS524/MS514H/MX525 MW526/TW526 Screen size Projection distance mm DiagonalAverage Connection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio MS524/ MW526/ MS514H/ TW526 MX525Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementSetting the presentation timer Resetting current or all picture modesSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Save 3D Settings Apply 3D SettingsTeaching Template Description Picture menu Source menu Function Description Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorSystem Setup Basic menu Function Description Presentation TimerInstallation SettingsLock BackgroundColor Splash ScreenSystem Setup Advanced menu Function Description Reset AllClosed CaptionCurrent SystemStatus Maintenance Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status MessageResetting the lamp timer Replacing the lampIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputKHz Supported timing for Hdmi Hdcp input MAC21Supported timing for Component-YPbPrinput TimingMHz Supported timing for Video and S-Video inputs NtscWarranty and Copyright information Limited warrantyCopyright Disclaimer