BenQ MS524/MS514H/MX525/MW526/TW526 Picture menu Source menu Function Description Picture Mode

Page 41

2. PICTURE menu

3. SOURCE menu

Function

Description

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 27 for details.

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 27

 

for details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

page 28 for details.

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 28 for details.

 

 

Adjusts the color saturation level -- the amount of each color in a

Color

video image. See "Adjusting Color" on page 28 for details.

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

Adjusts the red and green color tones of the image. See "Adjusting

Tint

Tint" on page 28 for details.

This function is only available when a Video or S-Video signal is selected and

 

 

the system format is NTSC.

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 28 for details.

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

Brilliant Color

See "Adjusting Brilliant Color" on page 28 for details.

 

 

Color

See "Selecting a Color Temperature" on page 28 for details.

Temperature

 

 

Color

 

Temperature

See "Setting a preferred color temperature" on page 29 for details.

Fine Tuning

 

 

 

3D Color

See "3D Color Management" on page 29 for details.

Management

 

 

 

Reset Picture

See "Resetting current or all picture modes" on page 30 for details.

Settings

 

Quick Auto

See "Switching input signal" on page 24 for details.

Search

 

 

 

Color Space

See "Switching input signal" on page 24 for details.

Conversion

 

 

 

Operation 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents MS524/MS514H/MX525/MW526 TW526 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingMS524/MS514H/MX525 Projection dimensionsObtaining a preferred projected image size Average MW526/TW526Screen size Projection distance mm Diagonal Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMS524/ MW526/ MS514H/ TW526 MX525 About the aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Teaching Template Description Save 3D SettingsApply 3D Settings Temperature Picture menu Source menu Function Description Picture ModeColor Temperature Fine Tuning 3D ColorTimer System Setup Basic menu Function Description PresentationInstallation SettingsBackground LockColor Splash ScreenReset All System Setup Advanced menu Function DescriptionClosed CaptionStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsKHz Timing chartSupported timing for PC input MAC21 Supported timing for Hdmi Hdcp inputMHz Supported timing for Component-YPbPrinputTiming Ntsc Supported timing for Video and S-Video inputsLimited warranty Warranty and Copyright informationCopyright Disclaimer
Top Page Image Contents