BenQ SP870 user manual Adjusting the projected image, Adjusting the projection angle

Page 27

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 2 quick-release adjuster feet. These adjusters change the picture height and projection angle.

To adjust the projector, slightly lift the front of the projector and press and hold the quick-release buttons on the both sides near bottom until the picture is positioned where you want it.

To retract the foot, hold up the front of the projector while pressing the quick-release buttons, then slowly lower the projector.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected picture becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 28 for details.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re- adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

The screen will be blank while AUTO is functioning.

Fine-tuning the image size and clarity

1.Adjust the projected image to the size that you need using the zoom ring.

2.Then sharpen the image by rotating the focus ring.

iii

i.Be aware of the vent where hot air comes from.

ii.Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Operation 27

Image 27

Contents SP870 Digital Projector WelcomeTable of contents 3000 m 10000 feet Important safety instructionsWith all windows rolled up Cigarette smoke may contaminate opticalImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Quick-release foot Projection lens Lens cap Projector exterior viewRear/lower side See Connection on page 16 for connection detailsProjector Controls and functionsDetails Remote controlStarts the FAQ function. See Utilizing FAQ Your own timer setting. See Setting22. D. Zoom + Remote control effective rangeMaking the remote control a wired control Operating the Laser pointerChoosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionWith a VGA cable With a VGA to DVI-A cable Connecting a monitorComputer using the D-SUB/COMP. Socket, not the DVI-Dsocket To connect the projector to a monitorBetter video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceWith a Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device With a Component Video cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationSecuring the projector Using the On-Screen Display OSD menusUsing a security cable lock Use / to highlight the System Setup Basic menu To leave the OSD menu, press MENU/EXIT Utilizing the password function Setting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageMagnifying and searching for details Correcting keystonePress About the aspect ratio Selecting the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode PC input signals D-Sub/Comp. analog RGB, and DVI-D DVI-DFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature About color temperaturesFollow these steps to utilize this function Setting the presentation timerRepeat steps 3 to 6 for other color adjustments Press MENU/EXIT to exit and save the settingsRemote paging operations To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW key? Using the OSD menuUtilizing FAQ function Hiding the imageFreezing the image Panel Key Lock menu and press To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentCreating your own startup screen Adjusting the soundAdjusting the sound level Turning off the Power on/off ring tonePersonalizing the On-Screen Display OSD menus Shutting down the projectorIf the projector is not properly On-Screen Display OSD Menus Menu structureMain menu Sub-menu Options Menu Position Center/Top-Left/Top-Right/Bottom Setup BasicReset All Settings AdvancedDisplay menu Picture menu Description of each menuBlank Timer Save SettingsPresentation Timer Auto Power OffSystem Setup Advanced menu Information menu Maintenance Care of the projectorLamp information Timing of replacing the lamp Setting Lamp Mode as EconomicSetting Auto Power Off Extending lamp lifeRemove the lamp cover from the projector Replacing the lampLoosen the screw that secures the lamp To slowly pull the lamp out of the projectorResetting the lamp timer Settings menuPress Enter and the Lamp Settings Indicators Troubleshooting Specifications Projector specificationsDimensions Supported timing for Video and S-Video inputs Timing chartSupported timing for Analog RGB input Supported timing for Component-YPbPrinputSXGA75 Supported timing for DVI-D Hdcp inputRegulation statements Other information

Related manuals

Manual 5 pages 12.86 Kb