BenQ SP870 Extending lamp life, Timing of replacing the lamp, Setting Lamp Mode as Economic

Page 45

Extending lamp life

The projection lamp is a consumable item that normally can last up to 2000-3000 hours with proper usage. To keep the lamp life as long as possible, you can do the following settings via the OSD menus.

Setting Lamp Mode as Economic

Using Economic mode reduces system noise and power consumption. If the Economic mode is selected, the light output will be reduced and result in darker projected pictures.

Setting the projector in Economic mode also extends the lamp operation life. To set Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp Mode menu and press / to select Economic.

Setting Auto Power Off

This function allows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of lamp life.

To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and press / . The time period can be set from 5 to 30 minutes in 5-minute increments. If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.

Timing of replacing the lamp

When the LAMP indicator light is red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the LAMP or TEMPerature indicator light still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 48 for details.

The following Lamp warning displays will remind you to change the lamp.

Status & Message

Status & Message

The lamp has been in operation for 2000 hours.

The lamp has been in operation for 3000 hours. It

 

Install a new lamp for optimal performance. If the

 

is strongly recommended that you replace the

 

projector is normally run with Economic Mode

 

lamp at this age. The lamp is a consumable item.

 

selected (See "Lamp Mode (Normal)" on page 43),

 

The lamp brightness diminishes with use. This is

 

you may continue to operate the projector until

 

normal lamp behavior. You can replace the lamp

 

the 3950 hour lamp warning appears.

 

whenever you notice that the brightness level has

 

Notice

 

significantly diminished. If the lamp is not

 

 

 

replaced beforehand, it must be replaced after

 

Order Replacement Lamp

 

3000 hours usage.

 

Lamp > 2000 Hours

 

Notice

 

 

 

Replace Lamp Now

 

OK

 

Lamp > 3000 Hours

 

 

 

 

 

 

Lamp usage time exceeded

The lamp has been in operation for 2950 hours. A

 

 

 

new lamp should be fitted to avoid the

 

OK

 

 

 

 

inconvenience when the projector runs out of

 

 

 

lamp time.

The lamp MUST be replaced before the projector

 

Notice

 

will operate normally.

 

Replace Lamp Soon

 

Notice

 

 

 

 

Lamp > 2950 Hours

 

Lamp-usage time exceeded

 

 

 

 

 

 

Replace lamp (refer to user manual)

 

 

 

Then reset lamp timer

 

OK

 

 

 

 

 

OK

 

 

 

 

Maintenance 45

Image 45
Contents SP870 Digital Projector WelcomeTable of contents With all windows rolled up Important safety instructionsCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewSee Connection on page 16 for connection details Quick-release foot Projection lens Lens capProjector Controls and functionsStarts the FAQ function. See Utilizing FAQ Remote controlYour own timer setting. See Setting DetailsMaking the remote control a wired control Remote control effective rangeOperating the Laser pointer 22. D. Zoom +Choosing a location Positioning your projectorObtaining a preferred projected image size Select your screen size Zoom Projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerComputer using the D-SUB/COMP. Socket, not the DVI-Dsocket Connecting a monitorTo connect the projector to a monitor With a VGA cable With a VGA to DVI-A cableConnecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a DVI-D source device Connecting a DVI-D source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableTo connect the projector to an S-Video/Video source device Connecting an S-Video or a composite Video source deviceStarting up the projector OperationUsing a security cable lock Using the On-Screen Display OSD menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystonePress About the aspect ratio Selecting the aspect ratioSelecting a picture mode Using Wall ColorPC input signals D-Sub/Comp. analog RGB, and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant ColorAbout color temperatures 3D Color ManagementRepeat steps 3 to 6 for other color adjustments Setting the presentation timerPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionHow to use the Timer ON/SHOW key? To cancel the timer, perform the following stepsUsing the OSD menu Remote paging operationsUtilizing FAQ function Hiding the imageFreezing the image Locking control keys To activate the High Altitude ModeOperating in a high altitude environment Panel Key Lock menu and pressAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Creating your own startup screenPersonalizing the On-Screen Display OSD menus Shutting down the projectorIf the projector is not properly On-Screen Display OSD Menus Menu structureMain menu Sub-menu Options Reset All Settings Setup BasicAdvanced Menu Position Center/Top-Left/Top-Right/BottomDisplay menu Picture menu Description of each menuPresentation Timer Save SettingsAuto Power Off Blank TimerSystem Setup Advanced menu Information menu Maintenance Care of the projectorLamp information Setting Auto Power Off Setting Lamp Mode as EconomicExtending lamp life Timing of replacing the lampLoosen the screw that secures the lamp Replacing the lampTo slowly pull the lamp out of the projector Remove the lamp cover from the projectorResetting the lamp timer Settings menuPress Enter and the Lamp Settings Indicators Troubleshooting Specifications Projector specificationsDimensions Supported timing for Analog RGB input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsSXGA75 Supported timing for DVI-D Hdcp inputRegulation statements Other information
Related manuals
Manual 5 pages 12.86 Kb

SP870 specifications

The BenQ SP870 is a cutting-edge projector designed to deliver high-quality visuals for both educational and professional settings. This projector stands out due to its advanced technology and robust features that cater to the demands of various presentations and multimedia applications.

One of the primary characteristics of the SP870 is its impressive resolution. With a native WUXGA resolution of 1920 x 1200, this projector ensures that images and videos are displayed with exceptional clarity and detail. The high resolution is particularly beneficial for presentations that involve intricate graphics, charts, or fine text, allowing viewers to see every detail without straining their eyes.

The SP870 is equipped with a brightness level of up to 5,000 ANSI lumens, making it suitable for use in environments with varying lighting conditions. Whether you're presenting in a well-lit conference room or a dimly lit classroom, the SP870 delivers bright and vibrant images, ensuring that your content is visible and impactful. The projector also features a high contrast ratio, which enhances the depth of colors and provides a more immersive viewing experience.

Another significant aspect of the BenQ SP870 is its color accuracy and technology. It utilizes BrilliantColor technology, which enhances color performance by improving the brightness of colors and allowing for a wider color spectrum. This results in rich, vivid colors that can engage and captivate an audience, making it an excellent choice for creative professionals and educators alike.

In terms of connectivity, the BenQ SP870 offers a variety of ports, including HDMI, VGA, and USB, allowing for easy connection to a range of devices such as laptops, tablets, and media players. This versatility makes it easy to use the projector in multiple settings, from boardrooms to classrooms.

Additionally, the projector is designed with user-friendly features such as a quick start-up time, allowing users to begin their presentations swiftly. Its lamp life, rated up to 4,000 hours in normal mode and 6,000 hours in eco mode, ensures longevity and reduces maintenance costs.

Overall, the BenQ SP870 is a robust projector equipped with high resolution, exceptional brightness, advanced color technologies, and versatile connectivity options. It is an ideal choice for professionals and educators seeking reliable and high-performance projection solutions.