BenQ SP870 user manual Magnifying and searching for details, Correcting keystone, Press

Page 28

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

To correct this, besides adjusting the height of the projector, you will need to manually correct it by following one of these steps.

Using the remote control

Press / on the control panel of the projector or remote

control to display the Keystone correction page. Press to correct

keystoning at the top of the image. Press to correct keystoning at the bottom of the image.

• Using the OSD menu

1. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2. Press to highlight Keystone and press ENTER. The Keystone

correction page displays.

Keystone

3.Press to correct keystoning at the top of the image or press

to correct keystoning at the bottom of the image.

Press / .

Press / .

MENU Back

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

Using the remote control

1.Press D. ZOOM +/- to display the Zoom bar.

2.Press D. ZOOM + to magnify the center of the picture. Press the

key repeatedly until the picture size is suitable for your need.

3.Use the directional arrows ( , , , ) on the projector or

remote control to navigate the picture.

4. To restore the picture to its original size, press AUTO. You can also press D. ZOOM -. When the key is pressed again, the picture is further reduced until it is restored to the original size.

• Using the OSD menu

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Digital Zoom and press ENTER. The Zoom bar displays.

3.Repeat steps 2-4in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps.

4.Press on the projector repeatedly to magnify the picture to a desired size.

5.To navigate the picture, press ENTER to switch to the paning

mode and press the directional arrows ( , , , ) to navigate the picture.

6.To reduce size of the picture, press ENTER to switch back to the zoom in/out function, and press AUTO to restore the picture to

its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

28 Operation

Image 28
Contents Welcome SP870 Digital ProjectorTable of contents Important safety instructions With all windows rolled upCigarette smoke may contaminate optical 3000 m 10000 feetImportant safety instructions Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Rear/lower sideSee Connection on page 16 for connection details Quick-release foot Projection lens Lens capControls and functions ProjectorRemote control Starts the FAQ function. See Utilizing FAQYour own timer setting. See Setting DetailsRemote control effective range Making the remote control a wired controlOperating the Laser pointer 22. D. Zoom +Positioning your projector Choosing a locationObtaining a preferred projected image size Select your screen size Projection dimensions ZoomConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor Computer using the D-SUB/COMP. Socket, not the DVI-DsocketTo connect the projector to a monitor With a VGA cable With a VGA to DVI-A cableConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting a DVI-D source device To connect the projector to a DVI-D source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cableConnecting an S-Video or a composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorUsing the On-Screen Display OSD menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsPress Selecting the aspect ratio About the aspect ratioUsing Wall Color Selecting a picture modePC input signals D-Sub/Comp. analog RGB, and DVI-D DVI-D Optimizing the imageFine-tuning the image quality in user modes Adjusting Brilliant Color Selecting a color temperatureAbout color temperatures 3D Color ManagementSetting the presentation timer Repeat steps 3 to 6 for other color adjustmentsPress MENU/EXIT to exit and save the settings Follow these steps to utilize this functionTo cancel the timer, perform the following steps How to use the Timer ON/SHOW key?Using the OSD menu Remote paging operationsHiding the image Utilizing FAQ functionFreezing the image To activate the High Altitude Mode Locking control keysOperating in a high altitude environment Panel Key Lock menu and pressAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Creating your own startup screenShutting down the projector Personalizing the On-Screen Display OSD menusIf the projector is not properly Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Setup Basic Reset All SettingsAdvanced Menu Position Center/Top-Left/Top-Right/BottomDescription of each menu Display menu Picture menuSave Settings Presentation TimerAuto Power Off Blank TimerSystem Setup Advanced menu Information menu Care of the projector MaintenanceLamp information Setting Lamp Mode as Economic Setting Auto Power OffExtending lamp life Timing of replacing the lampReplacing the lamp Loosen the screw that secures the lampTo slowly pull the lamp out of the projector Remove the lamp cover from the projectorSettings menu Resetting the lamp timerPress Enter and the Lamp Settings Indicators Troubleshooting Projector specifications SpecificationsDimensions Timing chart Supported timing for Analog RGB inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsSupported timing for DVI-D Hdcp input SXGA75Other information Regulation statements
Related manuals
Manual 5 pages 12.86 Kb

SP870 specifications

The BenQ SP870 is a cutting-edge projector designed to deliver high-quality visuals for both educational and professional settings. This projector stands out due to its advanced technology and robust features that cater to the demands of various presentations and multimedia applications.

One of the primary characteristics of the SP870 is its impressive resolution. With a native WUXGA resolution of 1920 x 1200, this projector ensures that images and videos are displayed with exceptional clarity and detail. The high resolution is particularly beneficial for presentations that involve intricate graphics, charts, or fine text, allowing viewers to see every detail without straining their eyes.

The SP870 is equipped with a brightness level of up to 5,000 ANSI lumens, making it suitable for use in environments with varying lighting conditions. Whether you're presenting in a well-lit conference room or a dimly lit classroom, the SP870 delivers bright and vibrant images, ensuring that your content is visible and impactful. The projector also features a high contrast ratio, which enhances the depth of colors and provides a more immersive viewing experience.

Another significant aspect of the BenQ SP870 is its color accuracy and technology. It utilizes BrilliantColor technology, which enhances color performance by improving the brightness of colors and allowing for a wider color spectrum. This results in rich, vivid colors that can engage and captivate an audience, making it an excellent choice for creative professionals and educators alike.

In terms of connectivity, the BenQ SP870 offers a variety of ports, including HDMI, VGA, and USB, allowing for easy connection to a range of devices such as laptops, tablets, and media players. This versatility makes it easy to use the projector in multiple settings, from boardrooms to classrooms.

Additionally, the projector is designed with user-friendly features such as a quick start-up time, allowing users to begin their presentations swiftly. Its lamp life, rated up to 4,000 hours in normal mode and 6,000 hours in eco mode, ensures longevity and reduces maintenance costs.

Overall, the BenQ SP870 is a robust projector equipped with high resolution, exceptional brightness, advanced color technologies, and versatile connectivity options. It is an ideal choice for professionals and educators seeking reliable and high-performance projection solutions.