Onkyo HT-RC370 Presetting AM/FM Stations, Using RDS excluding North American models, Mode

Page 29

Tuning into stations by frequency

You can tune into AM and FM stations directly by entering the appropriate frequency.

1 On the remote controller, press TUNER repeatedly

to select “AM” or “FM”, followed by D.TUN.

Deleting Presets

1

Select the preset that you want to delete.

 

See the previous section.

2

While holding down MEMORY, press TUNING

 

MODE.

The preset is deleted and its number disappears from the display.

(Actual display depends on the country.)

2 Within 8 seconds, use the number buttons to enter the frequency of the radio station.

For example, to tune to 87.5 (FM), press 8, 7, 5.

If you have entered the wrong number, you can retry after 8 seconds.

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.

1

Tune into the AM/FM station that you want to

 

store as a preset.

 

See the previous section.

2

Press MEMORY.

 

The preset number flashes.

 

 

 

 

 

 

 

 

 

 

 

 

(Actual display depends on the country.)

3

While the preset number is flashing (about 8

 

seconds), use PRESET e/rto select a preset from

 

1 through 40.

4

Press MEMORY again to store the station or

 

channel.

The station or channel is stored and the preset number stops flashing.

Repeat this procedure for all of your favorite AM/FM radio stations.

Note

You can name your radio presets for easy identification

(page 53). Its name is displayed instead of the band and frequency.

Selecting Presets

1 To select a preset, use PRESET e/ron the AV

receiver, or the remote controller’s CH +/–.

Tip

You can also use the remote controller’s number buttons to select a preset directly.

Using RDS (excluding North American models)

RDS works only in areas where RDS broadcasts are available.

When tuned into an RDS station, the RDS indicator lights. When the station is broadcasting text information, the text can be displayed.

What is RDS?

RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.).

The AV receiver supports four types of RDS information:

PS (Program Service)

When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Pressing DISPLAY will display the frequency for 3 seconds.

RT (Radio Text)

When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display as described in the next section.

PTY (Program Type)

This allows you to search for RDS radio stations by type (page 30).

TP (Traffic Program)

This allows you to search for RDS radio stations that broadcast traffic information (page 30).

Note

In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. This is not a malfunction.

If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.

En

29

Image 29
Contents HT-RC370 10 cm 4 at the rear. The rear edge of the shelf or Local regulations when disposing of batteriesBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Make sure you have the following accessories Supplied AccessoriesInstalling the batteries Aiming the remote controllerContents Services available may vary depending on the region FeaturesAmplifier ProcessingTHX Select2 Plus Front Panel Front & Rear PanelsFor detailed information, see the pages in parentheses DisplayZone 2 Line OUT jacks Rear PanelFront L/R, CENTER, Surr L/R, SB/FH/FW* L/R, Subwoofer Controlling the AV Receiver Remote ControllerDimmer button Display button Muting button Controlling the tunerConnecting Your Speakers Connecting the AV ReceiverConnecting the Speaker Cables Screw-type speaker terminalsSpeaker Connection Precautions Speaker ConfigurationAttaching the Speaker Cable Labels Number SpeakersUsing a Powered Subwoofer Using Dipole SpeakersBi-amping the Front Speakers TipConnecting a Power Amplifier About AV Connections Connecting AV componentsAV Cables and Jacks Hdmi cableAudio Return Channel ARC function Connecting Components with HdmiJack Components Assignable Audio Return Channel is set to AutoE F G H Connecting Your ComponentsJack/Port Components Assignable How to record a video sourceConnecting a Recording Component Connecting Onkyo uComponentsSystem On/Auto Power On Remote ControlConnecting the Power Cord Connecting the AntennasBe careful not to injure yourself when using thumbtacks Plug the power cord into an AC wall outletTurning On Turning On/Off the AV ReceiverTurning Off AV receiver comes on, the display lightsControlling Contents of USB or Network Devices Selecting the Language for the Onscreen Setup MenusPlayback Playing the Connected ComponentEnter Understanding Icons on the DisplayPlaying an iPod/iPhone via USB Listening to Internet Radio Playing a USB DeviceTop menu of Internet Radio Listening to Other Internet RadioRegistering My Favorites*1 Windows Media Player 12 Setup Windows Media Player 11 SetupPlaying Music Files on a Server Remote PlaybackUsing the Tuner Using Remote PlaybackTuning into Radio Stations Listening to AM/FM RadioMode Presetting AM/FM StationsUsing RDS excluding North American models Listening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Using the Automatic Speaker Setup Using Basic FunctionsMeasurement procedure First measurement positionAdjust the subwoofer volume level to 75 dB When you’ve finished making the settings, press` Cancel Use q/wto select a target, and use e/rto change the settingChanging the Speaker Setup Manually Error MessagesSelecting Listening Modes Using the Listening ModesAbout Listening Modes Following audio formats are supported by the listening modeExplanatory Notes Input SourceListening Modes Onkyo-Original DSP Listening ModesDSD*6 DTSTHX Listening Mode Description Input Speaker Source Layout Neo6Audyssey DSX *8 Listening Mode Description Input Speaker Source Layout Setting the Display Brightness Using the Home MenuUsing the Sleep Timer Displaying Source Information Using HeadphonesChanging the Input Display Selecting Speaker LayoutRecording Using Easy MacrosOn-screen Setup Menus Advanced SetupExplanatory Notes MenuInput/Output Assign ResolutionMonitor Out Hdmi InputDigital Audio Input Component Video InputAnalog Audio Input ` IN1, IN2Speaker Settings Speaker SetupSpeaker Distance Level Calibration Equalizer SettingsTHX Audio Setup Multiplex/Mono Audio AdjustDolby BGCDolby Volume DimensionVolume Leveler Half ModeTheater-Dimensional Source SetupAudyssey DSX LFE LevelReference Level Dynamic VolumeName Edit IntelliVolumeSync Picture Adjust Fixed Mode Charge ModeCharge Mode Audio SelectorVolume Setup Listening Mode PresetMiscellaneous DTS/DTS-ES/DTS-HDRemote ID Hardware SetupOSD Setup Tuner Auto Standby Dhcp Firmware UpdateNetwork Using the Audio Settings Remote Controller SetupLock Setup Re-EQ Late NightMusic Optimizer Connecting the Zone Speakers to an Additional Amplifier Connecting Your Zone 2 Speakers Directly to the AV receiverZone Making Zone 2 ConnectionsOperating on the remote controller Adjusting the Volume for ZoneControlling Zone 2 Components Muting ZoneUP-A1 Dock Using the Onkyo DockIPod/iPhone Playback via Onkyo Dock RI Dock Controlling Your iPod/iPhoneRandom Available buttonsLooking up for Remote Control Code Preprogrammed Remote Control CodesEntering Remote Control Codes Controlling Other ComponentsResetting Remote Mode Buttons Remote Control Codes for Onkyo Components Connected via uResetting the Remote Controller Controlling Other ComponentsVCR/PVR Enter Setup Search Repeat Random Mode8SOURCE*1 Input Guide TOP MenuDeleting Acquired Commands Learning CommandsFollowing buttons cannot learn new commands RemoteMaking Macros Using Normal MacrosRunning Macros Deleting MacrosAudio TroubleshootingPower Can’t select the Pure Audio listening mode There’s no sound with a certain signal formatSpeaker volume cannot be set as required About DTS signalsTuner Remote ControllerVideo Recording UP-A1 Dock for iPod/iPhoneZone Music Server and Internet RadioOthers USB Device PlaybackComponent Video Monitor OUT Important Note Regarding Video PlaybackUpdate procedure Firmware UpdateUpdating the Firmware via Network Before you startErrors during an update via network TroubleshootingError Code Description Updating the Firmware via USBOnkyo Sound & Vision Corporation Errors during an update via USBVideo Connection Formats Connection Tips and Video Signal PathSignal Selection OUT Audio Connection FormatsOutput Video Resolution ChartOutput Input 4K *2 1080p/24 1080i 720p 480p/576p 480i/576iOperations that can be performed with Connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Confirm the connecting and setting How to connect and setupConfirm the settings Operate with the remote controllerAbout Copyright Protection About HdmiSupported Audio Formats Network Requirements Network/USB FeaturesConnecting to the Network USB Device Requirements Server RequirementsServer playback Remote playbackAbout Dlna Supported Audio File FormatsAmplifier Section Tuner Section SpecificationsVideo Section GeneralOthers Audio Outputs4 0 0 7 3
Related manuals
Manual 2 pages 53.77 Kb

HT-RC370 specifications

The Onkyo HT-RC370 is a versatile and feature-rich AV receiver designed to enhance the home theater experience. Launched as a part of Onkyo’s acclaimed lineup, this receiver provides high-quality audio and video processing capabilities to satisfy both casual viewers and audiophiles alike.

One of the main features of the HT-RC370 is its support for both 7.2 channel surround sound and multiple audio formats, including Dolby TrueHD and DTS-HD Master Audio. This ensures immersive soundscapes for movies, music, and games, delivering a cinema-like experience right at home. The receiver offers a potent 100 watts per channel, which guarantees powerful sound output, making it suitable for various room sizes.

The HT-RC370 takes advantage of Onkyo’s advanced audio processing technologies, such as Audyssey MultEQ room correction. This system analyzes the acoustics of the space and automatically adjusts the speakers for optimal sound performance, significantly improving overall sound quality. Additionally, the receiver supports two subwoofers, enhancing low-frequency performance and creating a more balanced sound stage.

In terms of connectivity, the Onkyo HT-RC370 features an extensive range of options. It includes multiple HDMI inputs and outputs, allowing users to connect several devices, such as Blu-ray players, gaming consoles, and streaming devices, all while supporting 3D video and 4K upscaling capabilities. Other connectivity options include analog and digital audio inputs, as well as components like USB ports for easy access to music files.

An intuitive GUI (Graphical User Interface) enhances usability, and it provides straightforward control for both audio and video settings. The receiver also includes built-in network capabilities for streaming music from various online sources, such as Spotify and Pandora, providing flexibility for music lovers.

In summary, the Onkyo HT-RC370 combines robust features, advanced audio technologies, and extensive connectivity options to create an exemplary audio-visual experience. Whether you are hosting movie nights or enjoying your favorite music, this receiver provides the power, performance, and flexibility needed to elevate any entertainment setting.