Onkyo HT-RC370 instruction manual Audio Selector, Charge Mode, Fixed Mode

*2

*3

*4

*5

*6

*7

*1

Note

• “Picture Adjust” cannot be used with the NET input selector. This procedure can also be performed on the remote controller by using the Home menu (➔ page 40).

When a 3D video source is input, “Wide Mode” is fixed to “Full”.

When the “Picture Mode” setting is set to anything other than “Custom”, this setting cannot be used.

If the “Resolution” setting is set to “4K Upscaling” (➔ page 44), this setting is fixed to “Off”.

Press CLR if you want to reset to the default value.

If you are using the analog RGB input, this setting is not available.

If the “Game Mode” setting is set to “On”, this setting is fixed to “Off”.

Audio Selector

You can set priorities of audio output when there are both digital and analog inputs.

■Audio Selector

`ARC:

The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.*1

With this selection, the TV’s audio can be automatically selected as a priority among other assignments.

`HDMI:

This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is automatically selected as a priority.

`COAXIAL:

This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

`OPTICAL:

This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

`Multich:

The AV receiver always outputs analog signals from multichannel analog input.

`Analog:

The AV receiver always outputs analog signals.

Note

•The setting is stored individually for each input selector.

•This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.

•The “Audio Selector” settings cannot be used with the NET, USB and PORT (with connected component) input selectors.

•“Multich” can be selected only when the selector is set to “BD/DVD”.

*1 You can select “ARC” if you select the TV/CD input selector. But you cannot if you’ve selected “Off” in the “Audio Return Channel” setting (➔ page 58).

■Fixed Mode

`Off:

The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

`PCM:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced.

`DTS:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected in the “Audio Selector” setting, you can then specify the signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.

•If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.

•If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.

Note

•The setting is stored individually for each input selector.

•The setting will be reset to “Off” when you change the setting in “Audio Selector”.

Charge Mode

■Charge Mode

`Auto:

Power feeding is interrupted when your iPod/iPhone is fully charged.

`On:

Power feeding continues even if your iPod/iPhone is fully charged.

`Off:

Your iPod/iPhone is not charged.

You can specify how the power is fed to your iPod/iPhone when the AV receiver is in standby mode.

Note

•This setting cannot be selected when:

–the UP-A1 Dock with docked iPod/iPhone is not connected to the AV receiver, or

–the docked iPod/iPhone model is not supported.

•When the “Charge Mode” setting is set to “On”, or to “Auto” with your iPod/iPhone recharging, the SLEEP indicator is dimly lit in standby mode. In such conditions, the power consumption of the AV receiver slightly increases. With “Auto”, when the iPod/iPhone becomes fully charged, the SLEEP indicator goes off and the power consumption in standby mode is reduced.

En

55