Onkyo HT-RC370 When you’ve finished making the settings, press, ` Save, ` Cancel

Page 32

3 When you’ve finished making the settings, press

ENTER.

MultEQ XT: Auto Setup

 

AUDYSSEY

Speakers Type(Front)

Normal

Powered Zone 2

No

Subwoofer

Yes

Perform the “Speaker Setup” according to your speaker configuration:

Speakers Type(Front) (page 46)

Powered Zone 2 (page 46)

Subwoofer (page 46)

If you use a powered subwoofer(s), go to step 4. If not, go to step 5.

When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the optional unit setting may appear on the speaker setting menu.

4 Adjust the subwoofer volume level to 75 dB.

Test tones are played through the subwoofer. Use the volume control on the subwoofer.

Note

If your subwoofer does not have a volume control, disregard the level displayed and press ENTER to proceed to the next step.

If you set the subwoofer’s volume control to its maximum and the level displayed is lower than 75 dB, leave the subwoofer’s volume control at its maximum and press ENTER to proceed to the next step.

5 Use q/wto select “Audyssey Quick Start” or “Audyssey MultEQ XT Full Calibration”.

6 Press ENTER.

Audyssey MultEQ® XT Room Correction and Speaker Setup starts.

Test tones are played through each speaker as Audyssey MultEQ XT Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey MultEQ XT Room Correction and Speaker Setup, unless you want to cancel the setup. If you select “Audyssey Quick Start”, you will go to step 9.

7 Place the setup microphone at the next position, and then press ENTER.

Audyssey MultEQ XT performs more measurements. This takes a few minutes.

8 When prompted, repeat step 7.

9 Use q/wto select an option, and then press

ENTER.

MultEQ XT: Auto Setup

 

 

 

 

AUDYSSEY

-- Review Speaker Configuration --

Subwoofer

:

Yes

Front

:

100Hz

Center

:

40Hz

Surround

:

100Hz

Front Wide

:

None

Front High

:

None

Surround Back

:

120Hz

Surround Back Ch

:

2ch

Save

 

 

Cancel

 

 

The options are:

`Save:

Save the calculated settings and exit

Audyssey MultEQ XT Room Correction and

Speaker Setup.

`Cancel:

Cancel Audyssey MultEQ XT Room Correction

and Speaker Setup.

Note

You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using e/r.

10 Use q/wto select a target, and use e/rto change the setting.

After the results of Audyssey MultEQ XT have been saved, the menu will display the “Audyssey”

(page 51), “Dynamic EQ” (page 51), “Dynamic Volume” (page 52) settings.

Note

When “Audyssey Quick Start” has been used for measurement, “Audyssey” cannot be selected.

These settings are applied to all input selectors.

11 Press ENTER.

12 Disconnect the speaker setup microphone.

Note

You can cancel Audyssey MultEQ XT Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

Do not connect or disconnect any speakers during Audyssey MultEQ XT Room Correction and Speaker Setup.

If the AV receiver is muted, it will be unmuted automatically when Audyssey MultEQ XT Room Correction and Speaker Setup starts.

Changes to the room after Audyssey MultEQ XT Room Correction and Speaker Setup requires you run Audyssey MultEQ XT Room Correction and Speaker Setup again, as room EQ characteristics may have changed.

En

32

Image 32
Contents HT-RC370 Local regulations when disposing of batteries 10 cm 4 at the rear. The rear edge of the shelf orBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Supplied Accessories Make sure you have the following accessoriesInstalling the batteries Aiming the remote controllerContents Features Services available may vary depending on the regionAmplifier ProcessingTHX Select2 Plus Front & Rear Panels Front PanelDisplay For detailed information, see the pages in parenthesesZone 2 Line OUT jacks Rear PanelFront L/R, CENTER, Surr L/R, SB/FH/FW* L/R, Subwoofer Remote Controller Controlling the AV ReceiverDimmer button Display button Muting button Controlling the tunerConnecting the AV Receiver Connecting Your SpeakersConnecting the Speaker Cables Screw-type speaker terminalsSpeaker Configuration Speaker Connection PrecautionsAttaching the Speaker Cable Labels Number SpeakersUsing Dipole Speakers Using a Powered SubwooferBi-amping the Front Speakers TipConnecting a Power Amplifier Connecting AV components About AV ConnectionsAV Cables and Jacks Hdmi cableConnecting Components with Hdmi Audio Return Channel ARC functionJack Components Assignable Audio Return Channel is set to AutoConnecting Your Components E F G HHow to record a video source Jack/Port Components AssignableConnecting Onkyo uComponents Connecting a Recording ComponentSystem On/Auto Power On Remote ControlConnecting the Antennas Connecting the Power CordBe careful not to injure yourself when using thumbtacks Plug the power cord into an AC wall outletTurning On/Off the AV Receiver Turning OnTurning Off AV receiver comes on, the display lightsSelecting the Language for the Onscreen Setup Menus Controlling Contents of USB or Network DevicesPlayback Playing the Connected ComponentEnter Understanding Icons on the DisplayPlaying an iPod/iPhone via USB Playing a USB Device Listening to Internet RadioTop menu of Internet Radio Listening to Other Internet RadioRegistering My Favorites*1 Windows Media Player 11 Setup Windows Media Player 12 SetupPlaying Music Files on a Server Remote PlaybackUsing Remote Playback Using the TunerTuning into Radio Stations Listening to AM/FM RadioMode Presetting AM/FM StationsUsing RDS excluding North American models Listening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Using Basic Functions Using the Automatic Speaker SetupMeasurement procedure First measurement positionWhen you’ve finished making the settings, press Adjust the subwoofer volume level to 75 dB` Cancel Use q/wto select a target, and use e/rto change the settingError Messages Changing the Speaker Setup ManuallyUsing the Listening Modes Selecting Listening ModesFollowing audio formats are supported by the listening mode About Listening ModesExplanatory Notes Input SourceOnkyo-Original DSP Listening Modes Listening ModesDTS DSD*6THX Listening Mode Description Input Speaker Source Layout Neo6Audyssey DSX *8 Listening Mode Description Input Speaker Source Layout Setting the Display Brightness Using the Home MenuUsing the Sleep Timer Using Headphones Displaying Source InformationChanging the Input Display Selecting Speaker LayoutUsing Easy Macros RecordingAdvanced Setup On-screen Setup MenusExplanatory Notes MenuResolution Input/Output AssignMonitor Out Hdmi InputComponent Video Input Digital Audio InputAnalog Audio Input ` IN1, IN2Speaker Setup Speaker SettingsSpeaker Distance Level Calibration Equalizer SettingsTHX Audio Setup Audio Adjust Multiplex/MonoDolby BGCDimension Dolby VolumeVolume Leveler Half ModeSource Setup Theater-DimensionalAudyssey DSX LFE LevelDynamic Volume Reference LevelName Edit IntelliVolumeSync Picture Adjust Charge Mode Fixed ModeCharge Mode Audio SelectorListening Mode Preset Volume SetupMiscellaneous DTS/DTS-ES/DTS-HDRemote ID Hardware SetupOSD Setup Tuner Auto Standby Dhcp Firmware UpdateNetwork Using the Audio Settings Remote Controller SetupLock Setup Re-EQ Late NightMusic Optimizer Connecting Your Zone 2 Speakers Directly to the AV receiver Connecting the Zone Speakers to an Additional AmplifierZone Making Zone 2 ConnectionsAdjusting the Volume for Zone Operating on the remote controllerControlling Zone 2 Components Muting ZoneUP-A1 Dock Using the Onkyo DockIPod/iPhone Playback via Onkyo Dock Controlling Your iPod/iPhone RI DockAvailable buttons RandomPreprogrammed Remote Control Codes Looking up for Remote Control CodeEntering Remote Control Codes Controlling Other ComponentsRemote Control Codes for Onkyo Components Connected via u Resetting Remote Mode ButtonsResetting the Remote Controller Controlling Other ComponentsEnter Setup Search Repeat Random Mode VCR/PVR8SOURCE*1 Input Guide TOP MenuLearning Commands Deleting Acquired CommandsFollowing buttons cannot learn new commands RemoteUsing Normal Macros Making MacrosRunning Macros Deleting MacrosAudio TroubleshootingPower There’s no sound with a certain signal format Can’t select the Pure Audio listening modeSpeaker volume cannot be set as required About DTS signalsTuner Remote ControllerVideo UP-A1 Dock for iPod/iPhone RecordingZone Music Server and Internet RadioUSB Device Playback OthersImportant Note Regarding Video Playback Component Video Monitor OUTFirmware Update Update procedureUpdating the Firmware via Network Before you startTroubleshooting Errors during an update via networkError Code Description Updating the Firmware via USBErrors during an update via USB Onkyo Sound & Vision CorporationVideo Connection Formats Connection Tips and Video Signal PathSignal Selection Audio Connection Formats OUTVideo Resolution Chart OutputOutput Input 4K *2 1080p/24 1080i 720p 480p/576p 480i/576iOperations that can be performed with Connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components How to connect and setup Confirm the connecting and settingConfirm the settings Operate with the remote controllerAbout Copyright Protection About HdmiSupported Audio Formats Network Requirements Network/USB FeaturesConnecting to the Network Server Requirements USB Device RequirementsServer playback Remote playbackSupported Audio File Formats About DlnaSpecifications Amplifier Section Tuner SectionVideo Section GeneralAudio Outputs Others4 0 0 7 3
Related manuals
Manual 2 pages 53.77 Kb

HT-RC370 specifications

The Onkyo HT-RC370 is a versatile and feature-rich AV receiver designed to enhance the home theater experience. Launched as a part of Onkyo’s acclaimed lineup, this receiver provides high-quality audio and video processing capabilities to satisfy both casual viewers and audiophiles alike.

One of the main features of the HT-RC370 is its support for both 7.2 channel surround sound and multiple audio formats, including Dolby TrueHD and DTS-HD Master Audio. This ensures immersive soundscapes for movies, music, and games, delivering a cinema-like experience right at home. The receiver offers a potent 100 watts per channel, which guarantees powerful sound output, making it suitable for various room sizes.

The HT-RC370 takes advantage of Onkyo’s advanced audio processing technologies, such as Audyssey MultEQ room correction. This system analyzes the acoustics of the space and automatically adjusts the speakers for optimal sound performance, significantly improving overall sound quality. Additionally, the receiver supports two subwoofers, enhancing low-frequency performance and creating a more balanced sound stage.

In terms of connectivity, the Onkyo HT-RC370 features an extensive range of options. It includes multiple HDMI inputs and outputs, allowing users to connect several devices, such as Blu-ray players, gaming consoles, and streaming devices, all while supporting 3D video and 4K upscaling capabilities. Other connectivity options include analog and digital audio inputs, as well as components like USB ports for easy access to music files.

An intuitive GUI (Graphical User Interface) enhances usability, and it provides straightforward control for both audio and video settings. The receiver also includes built-in network capabilities for streaming music from various online sources, such as Spotify and Pandora, providing flexibility for music lovers.

In summary, the Onkyo HT-RC370 combines robust features, advanced audio technologies, and extensive connectivity options to create an exemplary audio-visual experience. Whether you are hosting movie nights or enjoying your favorite music, this receiver provides the power, performance, and flexibility needed to elevate any entertainment setting.