3M MP8650 manual Troubleshooting, Service Information, Problem Possible Solutions

Page 23

Section 8: Troubleshooting

The MP8650 has been designed to be as simple and trouble-free to use as possible. If you should run into problems operating the projector, please review the troubleshooting information below.

Problem

Possible Solutions

Power does not come on

D

Power cord must be plugged into an electric outlet.

 

D

Power switch must be turned on.

No picture and sound

D

Set the projector to the correct input source.

 

D

Check all cable connections from input source to projector.

 

D Make sure the input source power is on.

Picture displays but no sound

D

Check all cable connections from input source to projector.

 

D

Press VOLUME then + on the remote control.

 

D

Press the MUTE button on the remote control.

Sound but no picture

D

Check all cable connections from input source to projector.

 

D

Adjust the picture brightness. Press MENU, then press SELECT.

Weak saturation, incorrect hue

D

Adjust picture saturation and hue (video only). Press MENU, then press

 

 

SELECT.

Picture is dark

D

Adjust the picture brightness and contrast. Press MENU, then press SELECT.

 

D

Lamp may need replacement. Call customer service for assistance. See

 

 

Service Information below.

Picture is not sharp and clear

D

Adjust focus and sharpness (video only). Press MENU, then press SELECT.

WARNING is flashing on the

D

Projector is overheating. Turn the projector off and let it cool for 30 minutes.

projection screen

 

Clean the air filter and check all ventilation holes for blockage.

LAMP indicator solid red,

D

Turn the power off and let the projector cool. If the LAMP indicator comes on

Power-On indicator blinking red

 

again there may be a problem with the lamp. Call customer service for

 

 

assistance. See Service Information below.

ªChange Lampº message displays

D

The Change Lamp message will display for 30 seconds after power on when

when projector is powered on

 

the lamp clock reaches 1000 hours. This lamp is old and should be replaced

 

 

by a qualified technician.

Power indicator is blinking red

D

Check the air cleaner to make sure it is fully closed and latched.

TEMP indicator is red

D

Turn the projector off and let it cool. Check the ventilation holes for blockage.

Remote control does not operate D Replace old batteries with fresh AAA batteries.

DThe polarity of the batteries (+/±) must match the decal on the remote control.

DPoint the remote control toward the projection screen so the signal will bounce back to the projector. Also make sure the remote control sensor on the front of the projector is not blocked from receiving the signal.

8-1. Service Information

For product information, product assistance, service information, or to order accessories, please call:

In U.S. or Canada: 1-800-328-1371

In other locations, contact your local 3M Sales office.

3M 1997

3M

Multimedia Projector MP8650

19

 

 

Image 23
Contents MP8650 Multimedia Projector Operators Guide Were easy to reach Unpack Set UpRemote Control MaintenanceAppendix Technical Information TroubleshootingTechnical Specifications AccessoriesIntended USE SafeguardsThank YOU for Choosing 3M WarrantyKeep Your Packing Materials Contents of Shipping BoxUnpack Inventory ListParts Identification List Machine CharacteristicsProduct Description Terminal Connection Panel Set UpCable Connections Computer RGB Input Connection Power ConnectionMonitor Loop-Through 640 x 480 mode Video/Audio Connection Video ConnectionPC Serial Mouse Cable RS-232C Serial Cable/Mouse Receiver ConnectionCarrying Handle Projector Set UpAmbient Light Distance to Viewing ScreenRear Projection Adjusting the Projector ElevationNow What? Turning On the Projector Operating the ProjectorAdjusting the Picture Adjusting Image Size and FocusAdjusting the Volume Video System Memory FunctionInverting the Image Image PositionTurning Off the Projector Setting Apple Macintosh Monitor Mode Windowed or CompressedMenu Languages Remote Control Buttons Remote ControlHow to Operate the Remote Control Replacing the Batteries Using the Mouse ButtonsMouse Receiver ± Apple Macintosh computer only Change Lamp Message Lamp InformationMetal Halide Projector Lamp Display Lamp Operation HoursCleaning MaintenanceProblem Possible Solutions TroubleshootingService Information Video Input Signal Terminal Technical SpecificationsSpecifications Diagonal Width Height Physical DimensionsProjector-to-Screen Distances Computer Video RGB Input Terminal Computer RGB Signal Connection ModesAppendix Technical Information ±1. MP8650 Lamp Replacement 110V machines onlyRead Command Format Write Command Format±2. Serial Command Codes ±2. Serial Command Codes DIN 8 Projector Dsub 9 Computer Blank