Onkyo TX-SR805, TX-SR875 Connecting Antennas, Connecting the Indoor FM Antenna, Other Models

Page 25

Connecting Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals

 

ANTENNA

AM

FM75

FM antenna jack

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

1 Attach the FM antenna, as shown.

■American Model

FM75

Insert the plug fully into the jack.

■Other Models

FM75

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

2 Use thumbtacks or something similar to fix the FM antenna into position.

Thumbtacks, etc.

Caution: Be careful that you don’t injure yourself when using thumbtacks.

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out- door FM antenna instead (see page 26).

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

1 Assemble the AM loop antenna, inserting the tabs into the base, as shown.

2 Connect both wires of the AM loop antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around).

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Push

Insert wire

Release

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer- cially available outdoor AM antenna (see page 26).

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents
TX-SR805 TX-SR875 Avis Important Safety InstructionsPower PrecautionsFor models having a power cord with a polarized plug FCC Information for UserFor British models PrecautionsContents Features Make sure you have the following accessories Supplied AccessoriesPower cord THX Ultra2Main Room Multiroom CapabilityZone 2 Room Zone 3 Room Front Panel Getting to Know the AV ReceiverGetting to Know the AV Receiver Display Rear Panel Digital Optical in 1, 2, and OUT Digital Coaxial in 1, 2,GND screw Front L/R, CENTER, Surr L/R, and Surr Back L/R SpeakersInstalling the Batteries Remote ControllerUsing the Remote Controller About the Remote Controller Modes Remote ControllerRECEIVER/TAPE Mode Remote Mode buttons Listening Mode buttonsTape mode Standby buttonDVD Mode CD/MD/CDR Modes Dock Mode Enjoying Home Theater Connecting Your SpeakersSubwoofer Surround back left and right speakers Connecting Your Speakers Connecting Your SpeakersConnecting the Speaker Cables Speaker Connection PrecautionsFully insert the bare wire Strip about 5/8Bi-amping Speaker Hookup Bi-amping the Front SpeakersBridged Speaker Hookup Bridging the Front Speakers TX-SR875 onlyConnecting the Indoor FM Antenna Connecting AntennasConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor FM Antenna Connecting AntennasConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingConnecting Audio and Video Signals to the AV Receiver Connecting Your ComponentsHdmi Monitor Setting Set to Yes Which Connections Should I Use?TV, projector, etc Video Signal Flow Chart DVD player, etc Hdmi Monitor Setting Set to NoAudio Signal Flow Chart DVD player, etc Audio Connection FormatsVideo Connection Connecting a TV or ProjectorAudio Connection HintOr the other Connecting a DVD playerDVD player Hooking Up the Multichannel InputVCR or DVR Connecting a VCR or DVR for PlaybackDigital Optical OUT Connecting a VCR or DVR for RecordingSatellite, cable, set-top box, etc About Hdmi Connecting Components with HdmiSupported Audio Formats About Copyright ProtectionAudio Signals Video SignalsMaking Hdmi Connections Game Console Connecting a Game ConsoleCamcorder, etc Connecting a Camcorder or Other AV ComponentConnecting a Turntable Connecting a CD PlayerStep CD playerConnecting a Power Amplifier Connecting a Cassette, CDR, MiniDisc, or DAT RecorderPower amplifier European model Connecting an RI DockConnecting the Power Cord Connecting Onkyo ComponentsMalfunction Some components may not support all Functions WorkDo the automatic speaker setup-this is essential Set the Power switch to the on positionTurning On the AV Receiver Turning On and StandbySpeaker Settings First Time SetupHdmi Monitor Setup First Time SetupButtons to select 1. Input/Output Assign, and then press EnterButtons to select Resolution Using the Hdmi OUT ButtonCurrent setting is displayed Press the Hdmi OUT buttonHdmi Input menu appears Hdmi Input SetupVersion OUTFirst Time Setup Assign, and then press Component Video Input SetupInput/Output Assign menu AppearsChanging the Input Display These are the default assignments Digital Input SetupDigital Input menu appears Input selector Audio inputUsing the Digital Input Button Buttons to select an input selec Analog Input SetupTor Using Audyssey MultEQ XT Automatic Speaker Setup Audyssey MultEQ XTMeasurement Positions 1st measurement positionConnect it to the Setup MIC Place the setup microphone atWhen prompted, place the setup Turn on the AV receiverWhen the calculations are com Error MessagesDisconnect the setup micro Phone Plete, the following screenWriting Error Speaker Detect ErrorOne of the front speakers has not been detected One of the surround speakers has not been detectedUsing a Powered Subwoofer Changing the Speaker Settings ManuallyReviewing the Results You want to review, and thenButtons to select 6. Miscella TV Format Setup Not North American modelsNeous, and then press Enter Buttons to select TV FormatHardware Setup menu appears AM Frequency Step Setup on some modelsButtons to select 7. Hardware Buttons to select AM FreqSelect a listening mode and enjoy SettingsSee Using the Listening Modes on Playing Your AV ComponentsListening to the Radio Tuning into AM/FM Radio StationsListening to AM/FM Stations Listening to the Radio Tuning into Stations by FrequencyDisplaying AM/FM Radio Information Followed by the D.TUN buttonWhat is RDS? Using RDS not North American modelRDS Program Types PTY This allows you to search RDS radio stations by type seeFinding Stations by Type PTY Displaying Radio Text RTListening to Traffic News TP Selecting Presets Presetting AM/FM StationsDeleting Presets Setting the Display Brightness Adjusting Speaker LevelsCommon Functions Muting the AV ReceiverUsing Headphones Using the Sleep TimerCommon Functions Displaying Source InformationSelecting Audio Inputs Specifying the Digital Signal Format Selecting with the Remote Controller Using the Listening ModesSelecting the Listening Modes Selecting on the AV ReceiverListening Modes Available for Each Source Format Using the Listening ModesAnalog and PCM Sources Sacd DSD, Dolby Digital, and Dolby Digital Plus SourcesDTS-ES TrueHD and DTS SourcesDTS-HD Sources About the Listening Modes Use this mode with any stereo movie e.g., TV, DVD, VHSSound is output by the front left and right speakers DTS NEO6DSD Onkyo Original DSP Modes Recording the Input Source RecordingRecording from Different AV Sources Menu Map Onscreen Setup MenusMain menu SubmenuUsing the Late Night Function Adjusting the Listening ModesUsing the Re-EQ Function Audio Adjust Adjusting the Listening ModesTone Control Settings Multiplex/Mono Settings Direct SettingPLIIx/Neo6 Settings Dolby Digital Settings Listening Mode PresetsTheater-Dimensional Setting LFE Level SettingsAudio formats supported by that input selector appear Speaker Setup Advanced SetupSpeaker Settings Buttons to select SubwooferCrossover frequency Advanced SetupDouble Bass Low-Pass Filter for the LFE ChannelButtons to select Double Bass Speaker Distance Speaker Level Calibration Equalizer Settings THX Audio Setup Buttons to select THX Sub Source SetupWoofer, and use the Left Name Edit IntelliVolumeSync You want to give a custom nameSatellite Radio When you’ve finished, useSirius Parental Lock Arrow Buttons To display the following screenVolume Setup Miscellaneous SetupVolume Display Maximum VolumeOSD Setup Remote Control Hardware SetupZone 2 and Zone Analog Multich 100 Lock SetupLock Connecting Your Zone 2 Speakers Directly to the AV receiver Connecting ZoneConnecting Your Zone 2 Speakers to an Amp in Zone Zone 2 and Zone102 Connecting Your Zone 3 SpeakersZone 2 and Zone Zone 2 Video Output TX-SR875 only103 Powered Zone 2 SettingUsing Zone 2 and Zone Zone 2/Zone 3 Out Settings104 105 On the remote controller, pressSelecting an Input Source for Zones Turning Off ZonesAdjusting the Tone of Zone Adjusting the Volume of Zones Muting ZonesAdjusting the Balance of Zones 106Using a Multiroom Kit with a Cabinet Using a Multiroom Kit with Zone 2/3Using a Multiroom Kit with Other Components 107Controlling Other Components Entering Remote Control Codes108 Remote Control Codes for Onkyo Components Connected via Resetting the Remote ControllerResetting the Remote Mode Buttons 109CH +/-, TV CH + 110CH + Eject111 Learning Commands112 Using MacrosMaking Macros Running Macros113 Troubleshooting114 Troubleshooting115 116 117 SpecificationsSpecifications 118Audio Outputs Control TerminalMemo Onkyo U.S.A. Corporation 120Onkyo Europe Electronics GmbH Onkyo Europe UK Office
Top Page Image Contents