Onkyo TX-NR515 instruction manual En-52, Speaker Setup, Speaker Settings

Speaker Setup				■ Powered Zone 2
				`No
1	2	3	4 “Setup” 5	`Yes:
				Zone 2 speakers can be used. (Powered Zone 2

enabled).

Main menu Speaker Setup Note

	• If the “Speakers Type (Front)” setting is set to “Bi-Amp”,
Some of the settings in this section are set automatically
	Powered Zone 2 cannot be used.
by Audyssey 2EQ® Room Correction and Speaker Setup	• When the “Powered Zone 2” setting is set to “Yes” and Zone 2
(➔ page 34).	is turned on, the surround back and front high speakers cannot be
	used.

Advanced Operations

■ Center*1, Surround*1

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None

■ Front High*1*2*3*5

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None

■ Surround Back*1*2*3*4

`Full Band

Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup function.

Speaker Settings

If you change these settings, you must run Audyssey 2EQ Room Correction and Speaker Setup again (➔ page 34).

If you bi-amp the front speakers, you must change the

“Speakers Type (Front)” setting. For details on speaker wire connection, see “Bi-amping the Front Speakers”

(➔ page 14).

Note

•When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

•Before you change these settings, turn down the volume.

■Speakers Type (Front)

`Normal:

Select this if you’ve connected your front speakers normally.

`Bi-Amp:

Select this if you’ve bi-amped your front speakers.

Speaker Configuration

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 34).

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies.

■Subwoofer

`Yes

`No

■Front

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None

Note

*1 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.

*2 If the “Surround” setting is set to “None”, this setting cannot be selected.

*3 If the “Speakers Type (Front)” setting is set to “Bi-Amp”, or the “Powered Zone 2” setting is set to “Yes” together with Zone 2 turned on, this setting cannot be selected.

*4 If anything else than “None” is selected in “Front High”, this setting is automatically set to “None”.

*5 If anything else than “None” is selected in “Surround Back”, this setting is automatically set to “None”.

■Surround Back Ch

`1ch:

Select if only one surround back speaker L is connected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” Setting is set to “None”, this setting cannot be selected.

•If the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, this setting cannot be selected.

En-52