Onkyo TX-NR515 instruction manual En-51, Component Video Input, Digital Audio Input, ` IN1

■BD/DVD, CBL/SAT, GAME, PC, TV/CD, EXTRA1,

EXTRA2

`HDMI1, HDMI2, HDMI3, HDMI4, HDMI5, HDMI6, HDMI7:

Select the input to which the component has been connected.

`- - - - -:

Output composite video and component video sources from the HDMI output. The video output signal from the HDMI output is the one configured in “Component Video Input”.

Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI7 have already been assigned, you must first set any unused input selectors to “- - - - -” or you will be unable to assign HDMI1 - HDMI7 to other input selectors.

Tip

•“EXTRA1” and “EXTRA2” can be selected as input sources in “Input” of “Quick Setup” (➔ page 45).

Note

•If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of “Component Video Input”.

•When an HDMI IN is assigned to an input selector as explained here, the same HDMI IN will be set as a priority in the “Digital Audio Input”. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” setting (➔ page 59).

•Do not assign an HDMI IN to the TV/CD selector while “HDMI Control(RIHD)” is set to “On” (➔ page 62), otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

•If you assign “- - - - -” to an input selector that is currently selected in “HDMI Through” (➔ page 62), the “HDMI Through” setting will be automatically switched to “Off”.

•“AUX” is used only for input from the front panel.

Component Video Input

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN, you must assign “IN1” to the “BD/DVD” input selector.

Here are the default assignments.

Input selector	Default assignment
BD/DVD	- - - - -
CBL/SAT	IN1
GAME	- - - - -
PC	- - - - -
AUX	- - - - - (Fixed)
TV/CD	- - - - -
EXTRA1	- - - - -
EXTRA2	- - - - -

■BD/DVD, CBL/SAT, GAME, PC, TV/CD, EXTRA1,

EXTRA2

`IN1:

Select the input to which the component has been connected.

`- - - - -:

Output composite video sources from the HDMI output.

Tip

•“EXTRA1” and “EXTRA2” can be selected as input sources in “Input” of “Quick Setup” (➔ page 45).

Note

•When composite video and component video sources are upconverted for HDMI OUT SUB, only signals with a resolution of 480i/576i are output and the resolution remains the same. If your TV doesn’t support this resolution, there will be no picture (➔ page 87).

•“AUX” is fixed to the “- - - - -” option.

En-51

Advanced Operations

Digital Audio Input

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector. Here are the default assignments.

Input selector	Default assignment
BD/DVD	COAXIAL1
CBL/SAT	COAXIAL2
GAME	OPTICAL1
PC	- - - - -
AUX	- - - - - (Fixed)
TV/CD	OPTICAL2
EXTRA1	- - - - -
EXTRA2	- - - - -

■BD/DVD, CBL/SAT, GAME, PC, TV/CD, EXTRA1,

EXTRA2

`COAXIAL1, COAXIAL2, OPTICAL1, OPTICAL2:

Select the input to which the component has been connected.

`- - - - -:

Select if the component is connected to an analog audio input.

Tip

•“EXTRA1” and “EXTRA2” can be selected as input sources in “Input” of “Quick Setup” (➔ page 45).

Note

•When an HDMI IN is assigned to an input selector in

“HDMI Input” (➔ page 50), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” (➔ page 59).

•Supported sampling rates for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

•“AUX” is fixed to the “- - - - -” option.