Mitsubishi Electronics XD450U user manual Bottom side Remote control, About the laser beam

MANUFACTURER : B MANUFACTURED JANUARY 2003

MADE IN CHINA

RADIAÇÃO LASER

EVITAR A EXPOSIÇÃO AO FEIXE APARELHO LASER DA CLASSE 2 POTÊNCIA MÁXIMA: 1mW COMPRIMENTO DE ONDA: 640 - 660 nm

Bottom side

1

2

Remote control

1
2
3
4		COMPUTER
5		1	2
	KEYSTONE		VIDEO
6		1	2
	EXPAND	P in P	AUTO POSITION
7	VOLUME		LASER
8
9
10	MENU	R-CLICK	ENTER
11	MUTE	STILL	16 : 9

12

MEMORY

SELECT

DVD VIDEO

3

23

22

21

20

19

18

17

16

15

14

13

24

1Adjustment foot (Front)

2 Lamp cover

3 Adjustment feet (Rear)

Caution:

Do not replace the lamp immediately after using the pro- jector because the lamp would be extremely hot and it may cause burns.

1 Laser aperture

2Transmission window

3 Indicator

4 POWER button

5 KEYSTONE button

6 EXPAND button

7 + , - (VOLUME) buttons

8 Mouse pointer

9 MENU button

10 STILL button

11 MUTE button (Audio/Video)

12 Programmable buttons

13 SELECT switch

14 MEMORY button

15 16 : 9 button

16 ENTER button

17 R-CLICK button (For mouse)

18 Direction buttons

19 LASER button

20 AUTO POSITION button

21 PinP button

22 VIDEO 1, 2 button

23 COMPUTER 1, 2 button

24 Left click button (For mouse)

• The + and - buttons are used in the KEYSTONE adjustment and the EXPAND mode in addition to the volume control.

• Pressing the LASER button emits a laser beam. Even when you keep holding down the LASER button, it is emitted only one minute. To keep emitting it longer, press the LASER button again.

• You can disable the LASER button to prevent laser radiation due to misuse of the button.

How to disable the LASER button

While holding the LASER button down, press the  button three times.

How to enable the LASER button

While holding the LASER button down, press the  button three times.

ENGLISH

EMITTED
LASER-	APERTURE
EXPOSURE
	THIS
IS
AVOID RADIATION
	FROM

C A U T I O N

LASER RADIATION DO NOT STARE INTO BEAM

WAVE LENGTH : 640-660nm

MAX OUTPUT : 1mW

CLASS 2 LASER PRODUCT

Comp l ies w i t h 21 CFR, 1040. 10 and 1040. 11

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEAU APPAREIL A LASER DE CLASSE2 LASER-STRAHLUNG

NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 RADIAZIONl LASER

NON GUARDARE NEL RAGGIO LUCE

APPARECCHIO LASER DI CLASSE 2

WAVE LENGTH :640-660nm MAX OUTPUT:1mW IEC60825-1:1993+A1:1997+A2:2001

INTERLINK K.K.

SHINODA BLDG 1-10-7 HIGASHIKANDA CHIYODA-KU,TOKYO 101-0031,JAPAN

About the laser beam

This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength : 640-660 nm)

Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)

CAUTION :

•Pressing the LASER button on the remote control emits a laser beam. Do not look into the laser beam directly. Do not point the laser beam at anyone. Looking at the laser beam directly may damage eyesight.

•Use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure.

•This remote controller cannot be repaired.

EN - 7