Mitsubishi Electronics HD1000 Setting up your projector, Setting up the screen, Basic setup

Page 10

Setting up your projector

Setting up the screen

Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection angle of the projector. (See below.)

•Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of the screen center.

•Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen makes the projected images washed-out and hard to view.

SCREEN SIZE

You can keep the image display area within the screen by setting SCREEN SIZE in the IMAGE menu according to the size of the actual screen.

When setting SCREEN SIZE to CINEMA SCOPE(2.35:1):

•CinemaScope size movies are projected in the full screen.

•Set ASPECT in the FEATURE menu to 16:9 when displaying Vista-size images. In this case, they are squeezed horizontally.

•When ASPECT in the FEATURE menu is set to AUTO and 480p, 720p, or 1080i signal is input, the part for displaying subtitles is not projected.

Basic setup

Determine the distance from the screen to the projector according to the size of the images to be projected. (See page 12.)

W

A B

A=B

•Do not place this projector on a carpet or blanket because the exhaust vent and the intake vent on the bottom surface are blocked and the projector would heat, causing a breakdown or fire.

•Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.

Adjusting the projection angle

This projector is provided with three feet for adjusting the projection angle on the bottom surface. Adjust the projection angle depending on the position of the projector.

Adjustment of the projection angle

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.

Screen

Adjustment feet (rear)

1.Tilt up the projector to the appropriate angle.

2.Press the foot adjustment buttons next to the adjustment feet (rear), and the adjustment feet will come out.

3.Release the buttons to lock the adjustment feet (rear) to that position.

4.Rotate the adjustment feet (rear) for fine adjustment.

After using the projector:

5.Put the adjustment feet (rear) back into the projector by pressing the foot adjustment buttons.

•If necessary, rotate the adjustment feet (front) for fine adjustment.

When projected images are distorted to a trapezoid:

When the screen and the projector are not placed perpendicularly to each other, projected images become trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments, adjust keystone. (See page 18.)

•When the keystone adjustment is applied, the correct aspect ratio may not be obtained.

•When the keystone adjustment is applied, the resolution lowers. In addition, vertical stripes ap- pear and straight lines bend in images with com- plicated patterns. To prevent such symptoms, keep the screen and the projector perpendicular to each other as much as possible.

•Though the projected image may be distorted momentarily when you change the setting value of the keystone adjustment, such symptom is not a malfunction.

•Though the projected image may be distorted depending on the setting value of the keystone adjustment and the type of the input signal, such symptom is not a malfunction. In such a case, adjust the setting value within the range where the projected image is not distorted.

•The setting value displayed at the time of the keystone adjustment may vary depending on the type of the input signal.

•The keystone mode does not function when the REAL mode is applied.

•Displayed image may be distorted during key- stone adjustment.

EN-10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HD1000 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards EN-4Never remove the cabinet Do not modify this equipment Do not keep using the damaged projectorDo not unplug the power cord during operation Do not face the projector lens to the sunInserting the batteries into the remote control Checking accessoriesPreparing your projector USB terminal OverviewControl area Terminal panel Trigger terminalAdjustment foot Front Lamp cover Adjustment feet Rear Remote controlUsing the picture quality adjusting buttons Preparing your projectorReception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleTo cancel the menu With the Installation menu See page 24 for menu settingTrigger terminal When the aspect ratio of the image is Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceBasic home theater system connection Connecting the projector to video equipmentViewing video images PreparationWhen a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminalPlugging in the power cord Projecting images To stop projecting When projected images are distorted to a trapezoidFollowing cases With the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord For analog connectionProjecting images Viewing computer images When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonMenu operation Menu operation How to set the menusAvailable settings in the menus Image menuInstallation menu Feature menuTo enable the stored image quality settings Signal menuTo store the settings AV memoryTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp To adjust the ratio of change in brightness Gamma ModeTo adjust the vertical position LPFTo enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampReset of the lamp operation time Cleaning of the projector and the ventilation slotsCleaning of the lens Replacing the lampSolution TroubleshootingProblem No image appears on the screenProblem Solution TroubleshootingNo image appears on the screen Problem Solution Images are not displayed correctlyOthers Problem Solution Kensington LockNormal condition IndicatorsPower Status Condition Possible Solution Abnormal conditionDimension drawings unit mm SpecificationsSpecifications ConnectorsReplacement part Option/not included in the box VLT-HC910LPMitsubishi Projector Contact Information

HD1000 specifications

The Mitsubishi Electronics HD1000 is a powerful and versatile projector designed to meet the needs of professionals and educators alike. Known for its remarkable image quality and advanced features, the HD1000 has become a popular choice in various settings, including conference rooms, classrooms, and home theaters.

One of the standout features of the HD1000 is its high-definition resolution. With a native resolution of 1920x1080 pixels, this projector delivers stunning images with exceptional clarity and detail. This makes it ideal for displaying presentations, videos, and other visual content, ensuring that every detail can be seen by the audience.

The brightness of the HD1000 is another notable characteristic, boasting a luminous output of up to 3000 ANSI lumens. This high brightness level allows it to perform well even in well-lit environments, making it suitable for daylight use in larger rooms. Additionally, the contrast ratio of 10,000:1 enhances the overall visual experience, providing rich colors and deep blacks that contribute to an immersive viewing experience.

Mitsubishi has incorporated advanced technological features in the HD1000 to enhance its functionality. The projector supports 3D content, allowing users to present dynamic visuals that engage and captivate audiences. The seamless integration of 3D technology is ideal for educational institutions where interactive and engaging content is crucial for effective learning.

Another prominent feature is the projector's connectivity options. The HD1000 includes multiple input ports, such as HDMI, VGA, and composite video, ensuring compatibility with various devices, including laptops, Blu-ray players, and gaming consoles. This flexibility makes it easy to switch between different sources without the hassle of complicated setups.

Furthermore, the HD1000 is designed with energy efficiency in mind. It employs eco-friendly technologies that reduce power consumption when not in active use, extending the lifespan of the lamp and minimizing operational costs. This is an essential feature for businesses and schools looking to reduce their environmental footprint while ensuring reliability and performance.

In terms of user experience, the HD1000 features an intuitive interface and remote control, allowing for effortless operation and adjustments. Its compact and lightweight design ensures portability, making it easy to transport and set up in various locations.

In summary, the Mitsubishi Electronics HD1000 is a versatile and feature-rich projector that excels in delivering high-definition visuals. With its impressive brightness, advanced connectivity, and energy-efficient design, it serves as an excellent choice for any professional setting or educational institution.
Top Page Image Contents