Mitsubishi Electronics HD1000 user manual Projecting images

Page 21

C. Projecting images

Preparation:

•Remove the lens cap.

•Turn on the power of the connected computer.

FOCUS ring

ZOOM ring

POWER button

 

 

POWER STATUS

 

 

COMPUTER button

ON ( I ) button HDMI button

COMPUTER button

ENGLISH

1.Confirm the POWER indicator lights-up red.

•If the projector was turned off before the lamp had cooled down sufficiently, the fan may start rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the power button to turn back on the POWER indicator.

2.Press the POWER button on the projector or ON ( I ) button on the remote control.

•It may take about one minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a prod- uct malfunction.

•The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See pages 33 and 36.)

3.Select an input source.

•Press the COMPUTER button on the projector or the COMPUTER or HDMI button on the remote control that is corresponding to the terminal in use.

•The input source is switched between COMPUTER and HDMI every time you press the COMPUTER button on the projector.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button. (See page 22.)

•The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.

•The COMPUTER and HDMI buttons don’t function while the menu is being displayed.

• When COMPUTER is chosen as the source, images supplied from the computer may flicker. Press the or button on the remote control to reduce flicker, if it occurs.

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)

6.Adjust the size of the projected image by turning the ZOOM ring.

7.Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

EN-21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents HD1000 Risk of Electric Shock Do not Open When using the projector in EuropeContents EN-4 Important safeguardsDo not unplug the power cord during operation Do not keep using the damaged projectorNever remove the cabinet Do not modify this equipment Do not face the projector lens to the sunChecking accessories Inserting the batteries into the remote controlPreparing your projector Control area Terminal panel OverviewUSB terminal Trigger terminalUsing the picture quality adjusting buttons Remote controlAdjustment foot Front Lamp cover Adjustment feet Rear Preparing your projectorOperational range of the remote control Using the remote controlReception angle Front of projector Rear of projectorSetting up the screen Setting up your projectorBasic setup Adjusting the projection angleWith the Installation menu See page 24 for menu setting To cancel the menuTrigger terminal When the aspect ratio of the screen is Setting up your projectorWhen the aspect ratio of the image is Screen size and projection distanceViewing video images Connecting the projector to video equipmentBasic home theater system connection PreparationConnecting to a DVD player or Hdtv decoder Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesConnection for video equipment having a DVI-D terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images When projected images are distorted to a trapezoid To stop projectingFollowing cases How to change the settings Setting the aspect ratioWith the remote control With the Feature menuPlugging the power cord Connecting the projector to a computerViewing computer images For analog connectionProjecting images Example of the setting procedure for external output When connecting to a notebook computerViewing computer images Auto Position buttonMenu operation Available settings in the menus How to set the menusMenu operation Image menuFeature menu Installation menuTo store the settings Signal menuTo enable the stored image quality settings AV memoryTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature To adjust the ratio of change in brightness Gamma ModeLPF To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionReplacing the lamp Interval of lamp replacementCleaning of the lens Cleaning of the projector and the ventilation slotsReset of the lamp operation time Replacing the lampProblem TroubleshootingSolution No image appears on the screenNo image appears on the screen Problem Solution TroubleshootingProblem Solution Images are not displayed correctlyKensington Lock Others Problem SolutionPower Status Condition Possible Solution IndicatorsNormal condition Abnormal conditionSpecifications Dimension drawings unit mmReplacement part Option/not included in the box ConnectorsSpecifications VLT-HC910LPMitsubishi Projector Contact Information

HD1000 specifications

The Mitsubishi Electronics HD1000 is a powerful and versatile projector designed to meet the needs of professionals and educators alike. Known for its remarkable image quality and advanced features, the HD1000 has become a popular choice in various settings, including conference rooms, classrooms, and home theaters.

One of the standout features of the HD1000 is its high-definition resolution. With a native resolution of 1920x1080 pixels, this projector delivers stunning images with exceptional clarity and detail. This makes it ideal for displaying presentations, videos, and other visual content, ensuring that every detail can be seen by the audience.

The brightness of the HD1000 is another notable characteristic, boasting a luminous output of up to 3000 ANSI lumens. This high brightness level allows it to perform well even in well-lit environments, making it suitable for daylight use in larger rooms. Additionally, the contrast ratio of 10,000:1 enhances the overall visual experience, providing rich colors and deep blacks that contribute to an immersive viewing experience.

Mitsubishi has incorporated advanced technological features in the HD1000 to enhance its functionality. The projector supports 3D content, allowing users to present dynamic visuals that engage and captivate audiences. The seamless integration of 3D technology is ideal for educational institutions where interactive and engaging content is crucial for effective learning.

Another prominent feature is the projector's connectivity options. The HD1000 includes multiple input ports, such as HDMI, VGA, and composite video, ensuring compatibility with various devices, including laptops, Blu-ray players, and gaming consoles. This flexibility makes it easy to switch between different sources without the hassle of complicated setups.

Furthermore, the HD1000 is designed with energy efficiency in mind. It employs eco-friendly technologies that reduce power consumption when not in active use, extending the lifespan of the lamp and minimizing operational costs. This is an essential feature for businesses and schools looking to reduce their environmental footprint while ensuring reliability and performance.

In terms of user experience, the HD1000 features an intuitive interface and remote control, allowing for effortless operation and adjustments. Its compact and lightweight design ensures portability, making it easy to transport and set up in various locations.

In summary, the Mitsubishi Electronics HD1000 is a versatile and feature-rich projector that excels in delivering high-definition visuals. With its impressive brightness, advanced connectivity, and energy-efficient design, it serves as an excellent choice for any professional setting or educational institution.
Top Page Image Contents