Mitsubishi Electronics HD1000 user manual Trigger terminal, To cancel the menu

Page 11

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for instal- lation. For details, con- sult your dealer.

•The warranty on this projector does

not cover any damage caused by use of any non- recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

•When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 25.

•When the projector is mounted on the ceiling, im- ages may appear darker than those projected in the case of tabletop mounting. This isn’t a product malfunction.

•Ask your installation specialist to provide an A/C power switch. When you do not use the projector, be sure to shut down the main power by the switch.

•Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a breakdown.

•Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.

Rear projection

Ask a specialist for installation. For details, consult your dealer.

•For rear projec- tion, set IMAGE REVERSE in the

INSTALLATION menu to MIRROR. See page 25.

Caution:

•Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the projector to facilitate ventilation.

•Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

•Do not use the projector in the following locations and manners, which may cause fire or electric shock.

•In a dusty or humid place.

•In a sideways or upside-down position.

•Near a heater.

•In an oily, smoky, or damp place such as a kitchen.

•In direct sunlight.

•Where the temperature rises high, such as in a closed car.

•Where the temperature is lower than +41ºF (or +5ºC) or higher than +95ºF (or +35ºC ).

TRIGGER terminal

The TRIGGER terminal on the rear of the projector is a terminal that outputs a 12 V signal to control an externally connected device (electric screen) when images are projected.

HDMI IN

 

COMPONENT VIDEO IN

 

 

S-VIDEO IN

SERIAL

USB

 

 

TRIGGER

VIDEO IN

TRIGGER

To externally connected device

Ring (NC)

Tip (12 V)

 

(Ground 0 V)

To use the TRIGGER terminal, set TRIGGER OUT to ON in the INSTALLATION menu. (The factory default is OFF.) Use the following steps to change the setting.

With the INSTALLATION menu: (See page 24 for menu setting.)

1. Display the INSTALLATION menu.

2.

Select TRIGGER OUT by pressing the or but-

 

ton.

3.

Select ON by pressing the or button.

To cancel the menu:

4. Press the MENU button.

Caution:

•Do not use the signal output from the TRIGGER terminal as a power for other devices.

•Do not link the TRIGGER terminal with an audio terminal of other device because that device may be damaged.

•The rated current for the TRIGGER terminal is 200 mA. If you use a current exceeding this rating, a failure may occur.

•For information about electric screens, please con- tact screen manufacturers.

ENGLISH

EN-11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents HD1000 Risk of Electric Shock Do not Open When using the projector in EuropeContents EN-4 Important safeguardsDo not face the projector lens to the sun Do not keep using the damaged projectorDo not unplug the power cord during operation Never remove the cabinet Do not modify this equipmentPreparing your projector Checking accessoriesInserting the batteries into the remote control Trigger terminal OverviewControl area Terminal panel USB terminalPreparing your projector Remote controlUsing the picture quality adjusting buttons Adjustment foot Front Lamp cover Adjustment feet RearFront of projector Rear of projector Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupTrigger terminal With the Installation menu See page 24 for menu settingTo cancel the menu Screen size and projection distance Setting up your projectorWhen the aspect ratio of the screen is When the aspect ratio of the image isPreparation Connecting the projector to video equipmentViewing video images Basic home theater system connectionViewing video images Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder When a TV tuner or VCR is connectedConnection for video equipment having a DVI-D terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images Following cases When projected images are distorted to a trapezoidTo stop projecting With the Feature menu Setting the aspect ratioHow to change the settings With the remote controlFor analog connection Connecting the projector to a computerPlugging the power cord Viewing computer imagesProjecting images Auto Position button When connecting to a notebook computerExample of the setting procedure for external output Viewing computer imagesMenu operation Image menu How to set the menusAvailable settings in the menus Menu operationFeature menu Installation menuAV memory Signal menuTo store the settings To enable the stored image quality settingsTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintTo adjust the ratio of change in brightness Gamma Mode Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureLPF To adjust the vertical positionTo cancel the password function Advanced featuresPassword function To enable the password functionReplacing the lamp Interval of lamp replacementReplacing the lamp Cleaning of the projector and the ventilation slotsCleaning of the lens Reset of the lamp operation timeNo image appears on the screen TroubleshootingProblem SolutionImages are not displayed correctly TroubleshootingNo image appears on the screen Problem Solution Problem SolutionKensington Lock Others Problem SolutionAbnormal condition IndicatorsPower Status Condition Possible Solution Normal conditionSpecifications Dimension drawings unit mmVLT-HC910LP ConnectorsReplacement part Option/not included in the box SpecificationsMitsubishi Projector Contact Information

HD1000 specifications

The Mitsubishi Electronics HD1000 is a powerful and versatile projector designed to meet the needs of professionals and educators alike. Known for its remarkable image quality and advanced features, the HD1000 has become a popular choice in various settings, including conference rooms, classrooms, and home theaters.

One of the standout features of the HD1000 is its high-definition resolution. With a native resolution of 1920x1080 pixels, this projector delivers stunning images with exceptional clarity and detail. This makes it ideal for displaying presentations, videos, and other visual content, ensuring that every detail can be seen by the audience.

The brightness of the HD1000 is another notable characteristic, boasting a luminous output of up to 3000 ANSI lumens. This high brightness level allows it to perform well even in well-lit environments, making it suitable for daylight use in larger rooms. Additionally, the contrast ratio of 10,000:1 enhances the overall visual experience, providing rich colors and deep blacks that contribute to an immersive viewing experience.

Mitsubishi has incorporated advanced technological features in the HD1000 to enhance its functionality. The projector supports 3D content, allowing users to present dynamic visuals that engage and captivate audiences. The seamless integration of 3D technology is ideal for educational institutions where interactive and engaging content is crucial for effective learning.

Another prominent feature is the projector's connectivity options. The HD1000 includes multiple input ports, such as HDMI, VGA, and composite video, ensuring compatibility with various devices, including laptops, Blu-ray players, and gaming consoles. This flexibility makes it easy to switch between different sources without the hassle of complicated setups.

Furthermore, the HD1000 is designed with energy efficiency in mind. It employs eco-friendly technologies that reduce power consumption when not in active use, extending the lifespan of the lamp and minimizing operational costs. This is an essential feature for businesses and schools looking to reduce their environmental footprint while ensuring reliability and performance.

In terms of user experience, the HD1000 features an intuitive interface and remote control, allowing for effortless operation and adjustments. Its compact and lightweight design ensures portability, making it easy to transport and set up in various locations.

In summary, the Mitsubishi Electronics HD1000 is a versatile and feature-rich projector that excels in delivering high-definition visuals. With its impressive brightness, advanced connectivity, and energy-efficient design, it serves as an excellent choice for any professional setting or educational institution.
Top Page Image Contents