Mitsubishi Electronics HD1000 Replacing the lamp, To replace the lamp, Cleaning of the lens

Page 32

Replacing the lamp (continued)

To replace the lamp:

 

1.

Reverse the projector gently.

 

2.

Loosen the screw (a) using a Phillips screwdriver (+), and

(b)

(a)

remove the lamp cover (b).

 

 

3.

Loosen the screws (c) using a Phillips screwdriver (+).

4. Pull up the handle.

5. Pull out the lamp box by the handle while holding the

(c)projector.

(c)

Important:

• Pull the lamp box out of the projector slowly. If it is pulled out quickly, the lamp may break scattering glass fragments.

• Do not spill liquid on the removed lamp box or do not place it near any flammable object or where children can reach to prevent injury or fire.

6.Load a new lamp box securely into the projector in the right orientation.

7.Put the handle back to the original position.

• Make sure that the handle is locked.

8.Tighten up the screws (c) using a Phillips screwdriver (+).

9. Tighten up the screw (a) using a Phillips screwdriver (+) to secure the lamp cover.

Reset of the lamp operation time

Plug in the power cord and reset the lamp operation time by holding down the , , and POWER buttons on the control panel at the same time about three seconds.

•Unless these three buttons are pressed at the same time, the lamp operation time isn’t reset.

•Make sure that the STATUS indicator blinks twice and the lamp operation time is reset successfully.

•The projector doesn’t turn on if the lamp cover isn’t attached securely.

•Be sure to reset the lamp operation time whenever you replace the lamp.

•Do not reset the lamp operation time unless you replace the lamp.

•The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

•Contact your dealer for a new lamp.

•This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)

Maintenance

Warning:

Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating.

Caution:

Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector.

Cleaning of the projector and the ventilation slots

Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.

To protect the surface of the projector from fading or deteriorating:

•Do not spray insecticide on or inside the projector.

•Do not use benzine or thinner to clean it.

•Do not let rubber or plastic materials contact with projector.

Cleaning of the lens

Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.

EN-32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents HD1000 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards EN-4Do not keep using the damaged projector Do not unplug the power cord during operationNever remove the cabinet Do not modify this equipment Do not face the projector lens to the sunPreparing your projector Checking accessoriesInserting the batteries into the remote control Overview Control area Terminal panelUSB terminal Trigger terminalRemote control Using the picture quality adjusting buttonsAdjustment foot Front Lamp cover Adjustment feet Rear Preparing your projectorUsing the remote control Operational range of the remote controlReception angle Front of projector Rear of projectorSetting up your projector Setting up the screenBasic setup Adjusting the projection angleTrigger terminal With the Installation menu See page 24 for menu settingTo cancel the menu Setting up your projector When the aspect ratio of the screen isWhen the aspect ratio of the image is Screen size and projection distanceConnecting the projector to video equipment Viewing video imagesBasic home theater system connection PreparationConnecting to a video player, etc Connecting to a DVD player or Hdtv decoderWhen a TV tuner or VCR is connected Viewing video imagesConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminalPlugging in the power cord Projecting images Following cases When projected images are distorted to a trapezoidTo stop projecting Setting the aspect ratio How to change the settingsWith the remote control With the Feature menuConnecting the projector to a computer Plugging the power cordViewing computer images For analog connectionProjecting images When connecting to a notebook computer Example of the setting procedure for external outputViewing computer images Auto Position buttonMenu operation How to set the menus Available settings in the menusMenu operation Image menuInstallation menu Feature menuSignal menu To store the settingsTo enable the stored image quality settings AV memoryAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAdjusting projected images To adjust the tone of white Color TempAbout color temperature To adjust the ratio of change in brightness Gamma ModeTo adjust the vertical position LPFAdvanced features Password functionTo enable the password function To cancel the password functionInterval of lamp replacement Replacing the lampCleaning of the projector and the ventilation slots Cleaning of the lensReset of the lamp operation time Replacing the lampTroubleshooting ProblemSolution No image appears on the screenTroubleshooting No image appears on the screen Problem SolutionProblem Solution Images are not displayed correctlyOthers Problem Solution Kensington LockIndicators Power Status Condition Possible SolutionNormal condition Abnormal conditionDimension drawings unit mm SpecificationsConnectors Replacement part Option/not included in the boxSpecifications VLT-HC910LPMitsubishi Projector Contact Information

HD1000 specifications

The Mitsubishi Electronics HD1000 is a powerful and versatile projector designed to meet the needs of professionals and educators alike. Known for its remarkable image quality and advanced features, the HD1000 has become a popular choice in various settings, including conference rooms, classrooms, and home theaters.

One of the standout features of the HD1000 is its high-definition resolution. With a native resolution of 1920x1080 pixels, this projector delivers stunning images with exceptional clarity and detail. This makes it ideal for displaying presentations, videos, and other visual content, ensuring that every detail can be seen by the audience.

The brightness of the HD1000 is another notable characteristic, boasting a luminous output of up to 3000 ANSI lumens. This high brightness level allows it to perform well even in well-lit environments, making it suitable for daylight use in larger rooms. Additionally, the contrast ratio of 10,000:1 enhances the overall visual experience, providing rich colors and deep blacks that contribute to an immersive viewing experience.

Mitsubishi has incorporated advanced technological features in the HD1000 to enhance its functionality. The projector supports 3D content, allowing users to present dynamic visuals that engage and captivate audiences. The seamless integration of 3D technology is ideal for educational institutions where interactive and engaging content is crucial for effective learning.

Another prominent feature is the projector's connectivity options. The HD1000 includes multiple input ports, such as HDMI, VGA, and composite video, ensuring compatibility with various devices, including laptops, Blu-ray players, and gaming consoles. This flexibility makes it easy to switch between different sources without the hassle of complicated setups.

Furthermore, the HD1000 is designed with energy efficiency in mind. It employs eco-friendly technologies that reduce power consumption when not in active use, extending the lifespan of the lamp and minimizing operational costs. This is an essential feature for businesses and schools looking to reduce their environmental footprint while ensuring reliability and performance.

In terms of user experience, the HD1000 features an intuitive interface and remote control, allowing for effortless operation and adjustments. Its compact and lightweight design ensures portability, making it easy to transport and set up in various locations.

In summary, the Mitsubishi Electronics HD1000 is a versatile and feature-rich projector that excels in delivering high-definition visuals. With its impressive brightness, advanced connectivity, and energy-efficient design, it serves as an excellent choice for any professional setting or educational institution.
Top Page Image Contents