Mitsubishi Electronics EX320U, EW330U user manual Using the remote control for the first time

Page 10

Using the remote control for the first time

Pull the tab before using the remote control.

Remote control effective range

Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam.

• Do not let the IR transmitter of the remote control be shined by sunlight or fluorescent lamps directly.

Please keep the remote controller away from fluorescent lamps for over 2 m or the remote controller might become malfunction.

If the remote control is close to Inverter-Type fluorescent lamps, it might become ineffective from time to time.

If the remote control and the projector are within a very short distance, the remote control might become ineffective.

When you aim at the screen, the effective distance is less than 5 m from the remote control to the screen and reflecting the IR beams back to the projector. However, the effective range might change according to screens.

Replacing the remote control battery

1.Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

2. Insert the new battery in the holder. Note the positive polarity should face outward.

3. Push the holder into the remote control.

• Risk of explosion if battery is replaced by an incorrect type.

• Dispose of used batteries according to the instructions.

Use of a battery of wrong type may cause explosion. Use Lithium coin battery, type CR2025 only.

Dispose of used batteries according to your local regulations. Discard used battery promptly. Batteries may explode if mistreated. Do not recharge, disassemble, or dispose of in fire.

Be careful in handling the battery according to the instructions.

Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the battery if the remote control is not used for a long time.

Keep battery in original package until ready to use.

Never put battery in mouth for any reason as it can easily be accidentally swallowed. If battery is accidentally swallowed, contact your physician or your poison control center.

Dispose of the used battery with cellophane tape wrapping both ends of it.

EN-10

Image 10
Contents EX320U/EW330U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewFront/upper side Controls and functions ProjectorRemote control Magnifying and searching for details on page 26 forUsing the remote control for the first time Positioning your projector Choosing a locationWhen fine streaks are seen on projected images Obtaining a preferred projected image sizeEN-13 Front projection Layout of the projectorStandard 169 261 664 147 374 314 408 10.4Connection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting a monitor Connecting Video source devicesTo connect the projector to a monitor To connect the projector to an Hdmi device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus If you forget the password Utilizing the password functionSetting a password Entering the password recall procedureDisabling the password function Switching input signalChanging Color Space Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio EW330U EX320UEN-28 Setting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenImmediately To cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Locking control keys Adjusting the soundHiding the image Freezing the imageShutting down the projector Direct power offPersonalizing the projector menu display Standby Audio OutWatching 3D Content L RMode Resolution H x Horizontal Frequency Vertical Frequency If you are in a Dhcp environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a non-DHCP environmentPress / to reveal Controlling the projector using PJLink application About PJLinkUtilizing the password function PJLinksupported commandsHow to Use Network Function GlossaryMenu operation Menu systemSystem Setup Blank Timer Description of each menu DescriptionSetting Brightness Contrast Color Menu display time Lamp modeReset lamp timer Menu positionClosed Caption Enable Change passwordPower on lock SettingMaintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Spare lamp for EX320U/EW330U VLT-EX320LPResetting the lamp timer EN-53 Projector needs 90 seconds to cool down IndicatorsDown without the normal cooling down process Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation