Mitsubishi Electronics EW330U, EX320U Projector exterior view, Kensington Lock, Front/upper side

Page 7

Projector exterior view

Front/upper side

1	6
	6
2

9

3
4
	7
5	8

Rear/lower side

10		11	12		13		14						15			16

20

17

18

19

21

1.External control panel

(See "Projector" on page 8 for details.)

2.Lamp cover

3.Vent (heated air exhaust)

4.Quick-release button

5.Lens cover

6.Focus ring and Zoom ring

7.Front IR remote sensor

8.Projection lens

9.Vent (air intake)

Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.

10.RGB signal output socket

11.RGB (PC)/Component Video (YPbPr/ YCbCr) signal input socket x 2

12.HDMI input port

13.Serial control port

14.LAN (RJ-45) port

15.Audio input jack Audio output jack

16.S-Video input socket Video input socket

17.Kensington lock

18.AC power cord inlet

19.Quick-release foot

20.Security bar

21.Rear adjuster foot

Kensington Lock

This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.

Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below.

Kensington Technology Group 2855 Campus Drive

San Mateo, CA 94403, U.S.A.

Phone: +1- (650)572-2700 Fax: +1- (650)572-9675

ENGLISH

EN-7

Image 7

Contents EX320U/EW330U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewFront/upper side Projector Controls and functionsMagnifying and searching for details on page 26 for Remote controlUsing the remote control for the first time Choosing a location Positioning your projectorObtaining a preferred projected image size When fine streaks are seen on projected imagesEN-13 Front projection Layout of the projectorStandard 261 664 147 374 314 408 10.4 169To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting a monitor Connecting Video source devicesTo connect the projector to a monitor To connect the projector to a Component Video source device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Entering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordDisabling the password function Switching input signalChanging Color Space Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsEW330U EX320U Selecting the aspect ratioEN-28 Optimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenImmediately To cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Freezing the image Adjusting the soundHiding the image Locking control keysStandby Audio Out Direct power offPersonalizing the projector menu display Shutting down the projectorL R Watching 3D ContentMode Resolution H x Horizontal Frequency Vertical Frequency If you are in a non-DHCP environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a Dhcp environmentPress / to reveal About PJLink Controlling the projector using PJLink applicationPJLinksupported commands Utilizing the password functionGlossary How to Use Network FunctionMenu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color Menu position Lamp modeReset lamp timer Menu display timeSetting Change passwordPower on lock Closed Caption EnableCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampSpare lamp for EX320U/EW330U VLT-EX320LP Replacing the lampResetting the lamp timer EN-53 Please contact your dealer for assistance IndicatorsDown without the normal cooling down process Projector needs 90 seconds to cool downTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation